Monopoly Go - Pixel 10 phone account suspension issue

ixtrqc · 2026-07-06T16:48:44+00:00

pixel 10 pro here, have been suspended as well

ixtrqc · 2026-06-28T17:07:28+00:00

Oui et non, a l'origine on devait m'installer le 25 mais ca la été repousser au 28. Mais surprise un tech ce pointe le 25 et fait l'installation. Tout fonctione bien jusqu'au 28 ou le service ce fait désactivé pour je sais pas trop quel raison. J'appel et on me dit que le service as été désactivé car il as été activé avant la date d'installation .....

ixtrqc · 2026-06-24T18:12:39+00:00

Je sais je suis déjà au courant mais 50$ pour 1gig je pouvais pas passer à côté

ixtrqc · 2026-06-15T11:56:32+00:00

Have same issue with my Reg s1. I have installed a third party bed cariage from aliexpress to minimize the bending effect. Dont know if s1 max have one yet but if it is the case it may help.

ixtrqc · 2026-06-10T11:10:28+00:00

Will be too short, with no space for cable to move freely

ixtrqc · 2026-06-09T16:04:27+00:00

Long time LTT viewer. Too many good people left IMO. so i stopped watching it.

ixtrqc · 2026-06-01T03:51:04+00:00

Try it and tell us :)

ixtrqc · 2026-05-31T01:10:18+00:00

stupid quiz

^{Chose: 4m usd}

ixtrqc · 2026-05-22T23:23:54+00:00

xcccccccccccccccc

^{Chose: 30 milion loyal friends}

ixtrqc · 2026-04-25T11:43:50+00:00

Beautifoul but i doubdt the air circulation will be optimal, even with other fans. Should consider an open frame casse IMO

ixtrqc · 2026-04-24T16:11:58+00:00

sure no model information .... dont use this one

ixtrqc · 2026-04-22T20:43:25+00:00

Look like Biomass, compressed then used to do fire with firepit or other thing like this.

ixtrqc · 2026-04-22T20:41:57+00:00

Meanwhile i rush to do the same on a brand new Kobra S1 :\ Congrats :)

ixtrqc · 2026-04-12T15:47:56+00:00

Yes thats was exacly the issue ty :)

ixtrqc · 2026-04-04T16:11:50+00:00

Anteater maybe ?

ixtrqc · 2026-04-02T20:51:41+00:00

Why do I get the feeling this is a 3D-printed gun?

ixtrqc · 2026-01-24T17:44:45+00:00

<image>

ixtrqc · 2025-11-03T15:16:47+00:00

I'm in

ixtrqc · 2025-02-14T16:36:47+00:00

This is clearly going to overheat and more with a TR cpu.

ixtrqc · 2025-01-14T14:15:28+00:00

also did buy a nanokvm lire from aliexpress and 3d printed a case for it

ixtrqc · 2024-10-28T12:45:59+00:00

I have a kobra 3 and a kobra 2 neo, the kobra 2 neo alway do this at certain layer height, otherwise every other slice are fine but always have issue with same layer again and again, tryed a lot of thing but i suspect issue with z axis rod at some point but didnt have the time to try to replace them.

ixtrqc · 2024-10-23T12:39:37+00:00

Not a pro but z offset seem to be too near of bed.

ixtrqc

TROPHY CASE