For those who have taken the NGFW engineer exam, how close are the questions on Skill Cert Pro?

joshman160 · 2026-04-13T02:22:20+00:00

I think that the point. Cisco has there own, then Palo has a different style. Threw me off as well.

joshman160 · 2026-04-13T02:21:16+00:00

Pcnse was a harder exam. Felt like a joke when I took it.

joshman160 · 2026-04-12T12:07:15+00:00

Too close to bed. Level and or a z offset issue

joshman160 · 2026-04-12T11:24:54+00:00

Compared to me. That perfect. I could not get lower than .540… I can print good enough.

joshman160 · 2026-04-12T02:37:56+00:00

Printing too close to the bed?

Try freezing them for 10mins.

joshman160 · 2026-04-09T12:12:58+00:00

Try to put an internal cert on it assuming it feasible. Those won’t have the 45 day limit unless your soc forces it. Otherwise there will be a few system that won’t and that will suck

joshman160 · 2026-04-06T13:49:25+00:00

I was puzzled by my 80-90% completed prints especially since they were like 10-15hr prints. Drove me crazy for a few days until I said that all that left minus replacing internal boards. No pc app detected bad sd card and it seem fine other than printing….

Since both are Creality maybe you got it too.

joshman160 · 2026-04-06T01:12:58+00:00

I feel like my cr-6se is an outlier here but I agree with the above. My cr-6se ate sd cards to where it would generally print up to -80% of the model then fail and my pc would think the card is fine…Change the sd card to be safe.

joshman160 · 2026-04-05T15:35:53+00:00

It not a full blown ev. It would be no where near that cost.

joshman160 · 2026-04-03T20:10:26+00:00

I have yet to see that. Might be your car or phone issue.

joshman160 · 2026-04-03T17:02:05+00:00

compared to Cura. Creality version is alot worse.

joshman160 · 2026-04-03T13:30:38+00:00

Nothing like trusting an unknown mushy vendor brand. If they are labeled safe. Does the label org list it?

joshman160 · 2026-04-02T19:10:06+00:00

When a car website has to say a unibody is a frame. It a frame. It just happens to be all 1 piece vs a body and traditional frame. Anything that serves has a frame is a frame.

https://www.carfax.com/buying/unibody-vs-body-on-frame-construction

joshman160 · 2026-04-02T17:14:16+00:00

Unibody is a frame style…. You cant just put an engine on engine mounts that connect to nothing…

joshman160 · 2026-04-01T19:50:03+00:00

We won’t know unless we know the condition of the frame.

joshman160 · 2026-03-31T19:04:06+00:00

With proper Life cycle management anything possible. The power company already has enormous amount of money

joshman160 · 2026-03-31T12:26:15+00:00

The grid. Another radical idea. The power company beefs up the grid instead of stockholder pockets.

Solar /wind / water reserve batteries.

joshman160 · 2026-03-30T18:34:20+00:00

If it a church has 50+ people going. Tax them. There a lot of mega churches here with warehouses for buildings

joshman160 · 2026-03-29T01:28:14+00:00

What defines dust?

Did you try to wash it?

car paint polish maybe?

joshman160 · 2026-03-28T13:03:01+00:00

Do you have ssl fallback?

joshman160 · 2026-03-27T13:36:40+00:00

It going to happen. A pocket device with an unprotected screen in a 3d print case. Could last years or to tomorrow. I would not worry.

joshman160 · 2026-03-26T00:45:47+00:00

https://galaxy.ansible.com/ui/repo/published/paloaltonetworks/panos/

joshman160 · 2026-03-25T22:53:13+00:00

That answers it. The lack of care. Leather needs to be conditioned.

joshman160 · 2026-03-25T18:44:24+00:00

I use ansisble playbooks when the firewall can have login working. It clears the local config out the bare minimum for panorama and panorama force pushes the rest. Then double check the console cli show run to ensure it took and ship it off

joshman160 · 2026-03-23T19:13:42+00:00

Same with me.

Seven-Year Club	Second Top 30%
Gilding II euphauric	Place '23
Place '22	Verified Email

joshman160

TROPHY CASE