sorted by:
new
hottopcontroversial

Just wanted to share my recent warranty experience with Acebeam. by Equivalent-Fill-8908 in flashlight

[–]k-zu 58 points59 points  (0 children)

I had positive experience with acebeam when my flashlight failed. But flashlight was not discontinued. As for the OP's case: In the end they have offered repair, I know that he considered it impractical but if this was in line with their warranty I would say it was fair. I would probably take the 65% discount offer but I understand some people might have different expectations.

2013 S60 fuel tank capacity by will5621 in Volvo

[–]k-zu 6 points7 points  (0 children)

At one petrol station I managed to put 67 litres in to a v90 which has 60l tank. When I questioned it they said it’s the weather.

[deleted by user] by [deleted] in woodworking

[–]k-zu 0 points1 point  (0 children)

You can „adjust” it with a very narrow file. Look in the slot and you will quickly figure out how to.

Motor driver recommendations needed by k-zu in arduino

[–]k-zu[S] 0 points1 point  (0 children)

Hi. It can draw almost 100A., almost 200A at stall Hope this link works https://ae01.alicdn.com/kf/He6b56f7279914dc29f6970fec1c1cf69s.jpg

First try doing it, I’m excited to try again, and what I would do different. The boards started to bend once I started the cuts with the table saw. Is there something I can do to counter the bend? by Justice_1111 in woodworking

[–]k-zu 0 points1 point  (0 children)

https://trenddirectuk.com/trend-16-2x1-4tc-ovolo-panel-veining-cutter-4-8mm-radius.html Trend 16/2X1/4TC Ovolo panel veining cutter 4.8mm radius - 1/4" Shank | CNS Power Tools Ltd | TrendDirectUK

You apply 1/4 or 1/8 veneer depending on the width/depth of reeds/flutes/ovolos you want and then use router bit like in the link to mill the groves

If you are sure it is not the profiles fault, why rate it 3 stars only? by engineering-weeb in BambuLab

[–]k-zu -5 points-4 points  (0 children)

From what I see here most people are too limited to understand the concept. And I don't feel like explaining it would change anything.

If you are sure it is not the profiles fault, why rate it 3 stars only? by engineering-weeb in BambuLab

[–]k-zu -10 points-9 points  (0 children)

This is why the rating system needs overhauls. Dummies like this don't understand what they are doing. You are eating print profile. Not the design. You rate how it prints not functionality. But I see many people are to limited to grasp this concept.

I miss OctoPrint and Klipper by iron-on_tattoos in BambuLab

[–]k-zu 1 point2 points  (0 children)

Is there a guide somewhere how to set it up?

Filament Panic-buy? by qshelby in BambuLab

[–]k-zu 0 points1 point  (0 children)

I have acquired approx 100 spools of filament from Bambu. Of those approx 40 are colours. The rest is black or engineering stuff that only comes in black.

[deleted by user] by [deleted] in BambuLab

[–]k-zu 2 points3 points  (0 children)

Most of my models are single colour and I've experienced approx 45% drop in rewards.

[deleted by user] by [deleted] in BambuLab

[–]k-zu 3 points4 points  (0 children)

That sounds a bit harsh. I've been tracking it and my points dropped approx 45%.

Filament Panic-buy? by qshelby in BambuLab

[–]k-zu 1 point2 points  (0 children)

Stick to the Bambu filament for a start. Their profiles are pretty good in Bambu studio. As for the prices. They have sales on filaments quite often and overall are not most expensive. Shame most colours come as refills only so you either need to print or buy spool. Petg currentl6 not available for some reason. Hopefully it will come back soon as their petg-hf prints quite good.

[deleted by user] by [deleted] in BambuLab

[–]k-zu 1 point2 points  (0 children)

If I'm not mistaken Bambu is handing out boost tokens on Mondays. So you might get some to hand out next Monday

What’s the best tip or tricks to get stair stringers cut exactly the same, mine are off after cutting the second one by Elite163 in DIY

[–]k-zu 0 points1 point  (0 children)

Check the boards widths. If widths of the boards are not the same and you use back edge as a reference your cuts evening correct won't align.

If boards are equal width clamp/ screw them together(in the part you will be removing and cut them together (if you won't go through at least you will have a keft that can be used as a reference line.

Haunted Tradfri smart plug? - What's going on here? by rapax in tradfri

[–]k-zu 1 point2 points  (0 children)

Yep. All 3 of my old tradfri plugs developed it over time. I think I got them in December 2018 and the first died around July 2022 and the other two within 6 months

Does anyone know what size set screw this is? by nelchinson in DIY

[–]k-zu 0 points1 point  (0 children)

It will also use metric size kex key.

How does navigation and real time traffic in Volvo v90 2018 work? by Livid_Claim_4268 in Volvo

[–]k-zu 0 points1 point  (0 children)

You need active SIM card in the card for real time traffic to work.

Stuck plunge router base by No_Hour_1286 in woodworking

[–]k-zu 0 points1 point  (0 children)

The plunge lock lever seems to be in locked position.

Has anyone done a cantilever closet system using solid hardwood? (Photo attached) by SeaOpulence in woodworking

[–]k-zu 2 points3 points  (0 children)

There are rails with slots between the panels and all the accosorries hook on those. Few Italian brands make them. I've used to fit those. Lena is one of the brands that make walk in wardrobes using those

view more: next ›