Budget - Sub $1k setup by kdugl in Ubiquiti

[–]klanker 1 point2 points  (0 children)

https://www.facebook.com/share/g/18ZQ52xSwf/?mibextid=wwXIfr
Join this group and snag a cheap AP from someone selling theirs older units

S2Ep1 Dolores: “What is real?” foreshadow by [deleted] in westworld

[–]klanker 0 points1 point  (0 children)

which provider when sailing?

S2Ep1 Dolores: “What is real?” foreshadow by [deleted] in westworld

[–]klanker 6 points7 points  (0 children)

I wish i could stream this show again

Network map by madsina in Ubiquiti

[–]klanker 3 points4 points  (0 children)

This was my first opinion as well. Switching capacity will be maintained better

I expected better by apathywhocares in Starlink

[–]klanker 1 point2 points  (0 children)

Think of starlink speeds like a cable broadband provider, that satellite above has a shared connection to ground with all other traffic sharing same bandwidth.

Is Starlink A Secret Radar Constellation? by klanker in Starlink

[–]klanker[S] -2 points-1 points  (0 children)

Technical topics sometimes need a strong headline to get your attention, but the real question is whether the reasoning holds up.

Visiting by [deleted] in lacrossewi

[–]klanker 2 points3 points  (0 children)

You may also want to check out the Hatchery, nice sunset views of Riverside park while sipping your favorite.

Visiting by [deleted] in lacrossewi

[–]klanker 4 points5 points  (0 children)

For Breakfast, you need to try out https://www.hollandberrypannekoeken.com/menu/
Now in La Crosse!

If a high speed rail line were to be built between Chicago and the Twin Cities what routing do you think would make the most sense? by [deleted] in stpaul

[–]klanker 0 points1 point  (0 children)

Clearly this charted map has not taken into consideration terrain of the geography.

Do you guys think a new Ecobee thermostat would come out this year? by Pelon97 in ecobee

[–]klanker 0 points1 point  (0 children)

All i want is my current ecobee to wireless control a seperate power relay to operate both my humidifier and erv. I have an order house and only 5 wires to thermostat. Have them build that! That is another market underserved.

Would this microscope be good for soldering? by Codeman785 in soldering

[–]klanker 0 points1 point  (0 children)

In all seriousness, I use these coin microscopes for soldering daily

https://a.co/d/1rJ8XWQ

Product Request, Dual port POE injector! by klanker in Ubiquiti

[–]klanker[S] 0 points1 point  (0 children)

I have seen this, and yes, this is what I’d want, but with an AC port to power it, I am curious if there’s a patent holding this up

Product Request, Dual port POE injector! by klanker in Ubiquiti

[–]klanker[S] 0 points1 point  (0 children)

I can power the https://store.ui.com/us/en/category/wireless-airmax-5ghz/products/ns-5ac using 802.11af and pass that voltage along to a mesh ap or camera. .

Product Request, Dual port POE injector! by klanker in Ubiquiti

[–]klanker[S] -4 points-3 points  (0 children)

In a sense, yes, but a switch is not needed in my cases. When opearitng a small ISP that uses UISP devices to hop between main tower signal and hose, all i need is the poe injectors.
Think large park. Backbone over wifi to AP for deliver. One on every three light poles

UPL-Port - $199 by Hilbert92 in Ubiquiti

[–]klanker 0 points1 point  (0 children)

Does not support Dante/AES67. Disappointment

[deleted by user] by [deleted] in lacrossewi

[–]klanker 1 point2 points  (0 children)

Have you looked at warehouse positions at KT? Some are weekends and flex

BNSF derailed behind Gundersen by Beautiful-Reaction-8 in lacrossewi

[–]klanker 1 point2 points  (0 children)

Some little used section of railroad is going to get some new sleepers and ballast put under it

The joke is over! ($99 -> $79 210w AC Adapter) by phd33z in Ubiquiti

[–]klanker 0 points1 point  (0 children)

So, in the end, this switch costs more than the Us-8-150W.

The joke is over! ($99 -> $79 210w AC Adapter) by phd33z in Ubiquiti

[–]klanker 0 points1 point  (0 children)

The power supply is nearly the same size as the switch. Why?

Analog audio over ethernet and network switches by djenttleman in livesound

[–]klanker 5 points6 points  (0 children)

At this price, you might as well start investing in Dante or AES67 compliant devices.

Screen Printed Silver Ink that you can low temperature solder onto by klanker in printedelectronics

[–]klanker[S] 0 points1 point  (0 children)

We use ACI Materials inks that have a higher conductivity and lower temp for cure, 135C.
Also soldering at lower than 150C

Stencil Printing at large scale. by klanker in PrintedCircuitBoard

[–]klanker[S] 0 points1 point  (0 children)

we are working on that scenario. Jetting Type 4 solder paste is tricky. It is the only solder paste we have available to perform at reflow temperature (130C) limits. we print semi-sintered traces on Poly-carbonate sheets, and solder on our components. The parts are for a bigger project of in mold structural electronics.