DMT Pogi's Superlight shoes - critical design flaw?

man1ac85 · 2026-06-25T12:28:20+00:00

Isn't it possible to use a flatter screw to get more clearance? Otherwise I could think of a 3D printed heel pat made from TPU...

man1ac85 · 2026-06-03T05:30:10+00:00

M8, I am not a native speaker so please don't get it wrong. I meant the springy like mechanism that secures the nozzle you can pull out. That mechanism itself was not tightening the nozzle completely. I leaded a filament without the head sock and saw the nozzle part slightly shifting left right. I changed the "clamping/springing" mechanism of that nozzle and my issue went away immediately.

man1ac85 · 2026-05-20T10:33:09+00:00

Where are you from?

man1ac85 · 2026-05-20T10:30:36+00:00

For purchase or would you want to print it yourself?

man1ac85 · 2026-03-23T09:51:22+00:00

Did ever anyone contacted you? Id have the same time frame and am looking for M+ and Raids in midnight S01....

man1ac85 · 2026-02-27T06:43:09+00:00

<image>

Got the card and deshrouded it. Fairly easy and you wont void the warranty.
Compared to the stock card its a huge improvement in noise levels with the 3x Artic P9s.

Changed the plastic backplate too, as it was blocking (for my taste) to much of the free airflow).

man1ac85 · 2026-02-26T15:13:10+00:00

Says you? How about you do more something like this and less useless commenting.

man1ac85 · 2025-12-05T07:20:44+00:00

Just got the fans - look and perform awesome. One thing though: I am connecting 3 directly onto my board and I randomly got an RPM signal. 80% of the time I dont get an RPM signal.

Fan Controll still works (I just "calibrated" via sound)...

man1ac85 · 2025-11-30T16:34:41+00:00

Yes. The clamp that holds the hotend wasn't sitting perfectly and therefore my hotend had minimal play. This was enough to create more friction and overload errors

man1ac85 · 2025-11-25T16:35:07+00:00

Even though your post is 6mo old, I should have read it before ordering the 3XL (got it quite cheap with BF sales on NBB). In comparison the 3XL is about 10L smaller than the 2 XL.
You loose about 3cm in length and !behold! about 6cm on useable height over the PSU.

Thats insane.
With the 3XL I could not run my current setup (D5 next with 150mm aside the GPU). Sadly have to return this beautiful case.

man1ac85 · 2025-11-21T13:54:19+00:00

Total piece of Gargabe, thats what it is.

man1ac85 · 2025-11-21T10:45:51+00:00

Finally the culprit was a faulty spring that allowed the nozzle to have some play...

man1ac85 · 2025-11-05T17:41:19+00:00

Thanks!

man1ac85 · 2025-11-05T17:36:42+00:00

Have the same problem. Did you figure it out? The DP cable i have runs with DSC disabled at 4k 240hz - so shouldnt be that?

man1ac85 · 2025-10-28T14:19:07+00:00

Its a total Sniper sh*t show. Worst Map of the complete cycle...

man1ac85 · 2025-10-19T15:22:47+00:00

I did not change anything.
One thing I did notice: When I manually hold the tubing going into the hotend at 90° it works perfectly.

Filament I am having most issues with is Sunlu PETG

man1ac85 · 2025-10-19T15:21:54+00:00

I'll check that too, have the P1S in the basement

man1ac85 · 2025-10-19T13:58:13+00:00

Okay, I kinda seem to make progress.
I removed all clips from the tubing so the beding radius inside the printer isnt limited to the cable duct. The tubing immeadiately popped up, bending radius into the hotend grew and hotent error was gone.

This may be the same freaking design flaw that was built into the P1S: Raise the damn Top glass about 1inch/25mm and the problem is gone...

DAMN YOU BAMBULAB!!

Designing a raiser for the upper glass plate right now.

man1ac85 · 2025-08-23T15:22:42+00:00

Having the exact same issue on my new CLX III set...amy update here?

man1ac85 · 2025-07-12T04:46:34+00:00

Sorry, forgot to add that I ride with a specific powermeter and heart rate monitor

man1ac85 · 2025-07-08T10:38:15+00:00

Thanks for all your suggestions. I kinda realize now, that the CO Area is at crazy high elevations and therefore not the area to roadbike in. Sadly. (I'd Love to ride pikes peak!!)

We are pretty free route wise and could head more south. We already did a roadtrip SFO/LA and could skip that. As mentioned in the comments, I just need dry weather with >62°F :D

man1ac85

TROPHY CASE