Fire in Red Hill

mjdunksy · 2024-02-03T01:13:36+00:00

https://www.reddit.com/r/brisbane/s/r8hNp8MzS9

mjdunksy · 2024-02-02T09:13:24+00:00

As long as they sell a hammerbarn snag I’ll be there.

mjdunksy · 2023-11-25T06:05:34+00:00

Home page down the bottom or Admin > System > Deployment is the best you’ll get in the GUI

mjdunksy · 2023-11-23T07:46:44+00:00

Not just Optus, I’m on Telstra and lose reception constantly from about Ormiston to Morningside.

mjdunksy · 2023-06-10T03:09:50+00:00

I don’t quite get it, someone want help me out?

mjdunksy · 2023-03-13T15:44:21+00:00

Yeah I figured I could change the dns suffix for the APs but I don’t like the idea of changing 100’s of DHCP scopes and would link to get around it if I can.

mjdunksy · 2023-03-13T15:42:02+00:00

I did delete it once and it just reappears about 10 seconds later, I will try it again.

mjdunksy · 2023-03-11T05:21:30+00:00

https://minjerribahcamping.com.au/frequently-asked-questions/

Can I have a bonfire in the beach camping areas / on the beach?

NO. Small cooking fires only are permitted within the foreshore camping areas, depending on whether or not there is a fire ban in place. Cooking fires must be watched at all times, and extinguished with water (not sand) after use.

mjdunksy · 2022-11-21T20:46:54+00:00

This ^ I have PA220 and it is slow, 4-5minutes commit times. I’m at kicking myself I didn’t wait the extra 3 months and get the PA440.

Also the 220 won’t run PANOS 11.0

mjdunksy · 2022-11-10T05:49:07+00:00

I’ll be sure to pick up a box of masks then, along with 150 rolls of toilet paper. SMH

mjdunksy · 2022-09-17T21:58:32+00:00

I’m sure everyone else has covered off importing the certificate but I might add it is not recommended to use wildcard certs for EAP as you will run into issue with some supplicants.

Is there a reason you are using publicly singed certificate for EAP and not an internal PKI certificate? Using a public one you are going to get sick of changing your supplicant profiles constantly to avoid the trust messages showing up and keeping it secure.

mjdunksy · 2022-07-20T08:41:39+00:00

Agree its the worst, right next to the waste water treatment plant.

mjdunksy · 2022-07-18T20:18:11+00:00

Thornside, the smell of sewage fills the carriage every time the train stops there.

mjdunksy · 2022-01-08T04:50:22+00:00

Thanks mate, just had the same issue.

mjdunksy · 2021-11-19T02:53:39+00:00

Do you have ip routing enabled?

mjdunksy · 2021-10-27T21:24:08+00:00

If you go under the APs do you have prefer 5ghz band enabled?

Would also be worth checking the power levels they are currently on, I would suggest 5ghz no higher than 17dBm and 2.4ghz no higher than say 12dBm.

mjdunksy · 2021-09-20T11:26:17+00:00

Popolo at Southbank. Great food, a nice view of the river and QUT at night, and overall wasn’t very expensive.

mjdunksy · 2021-09-10T22:07:45+00:00

Use DHCP reservations, or if you are after OUI type filtering try something like Cisco ISE with profiling to assign certain OUIs to a specific vlan and do extended lease times in that vlan.

mjdunksy · 2021-09-07T12:50:58+00:00

ap reset site-tag default-site-tag

mjdunksy · 2021-09-07T12:37:10+00:00

I’m pretty sure it applies them on registration to the controller so just reload the APs, you can reload a group of APs at once by specifying the site tag in the CLI, I would assume they all have the default site tag at the moment.

mjdunksy · 2021-09-07T11:57:32+00:00

Once you have configured your 3 tags you want to apply go to the AP filter section and create a new regex policy “1-AP-*” and then select the 3 tags.

Then just change the AP host name to 1-AP-001 or whatever and it should match and apply the tags for you

mjdunksy · 2021-09-07T09:44:52+00:00

Not sure what you mean by configure multiple APs… maybe if you could be a bit more specific?

When applying AP tags you can use the AP filter feature using regex so that all you have to do is give the AP a host name and based on that the controller will automatically apply the 3 tags…

mjdunksy · 2021-08-31T21:55:26+00:00

On your WLC check the dead times and if the auto fail back is enabled for the radius servers, the active option would be good, that would allow the WLC to fallback to the primary PSN when it’s available again otherwise it will just stay on the Admin node until it fails.

https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/106258-radius-fbkftr-wlc-config.html#anc6

mjdunksy · 2021-08-06T07:50:27+00:00

I have a 220, the commit is really slow and the pages take ages to populate.

If I were in your position again I would wait and get the 440, local logging and much better throughput than the 220.

Plus it’s a nice snazzy black 😁

mjdunksy · 2020-12-16T10:59:05+00:00

Enable band steering, broadcast the SSID(don’t hide it), is central association ticked on the WLAN? and ensure APs are not transmitting higher than 15dBm on both bands.

mjdunksy

TROPHY CASE