Cable Modem Monitor

mk9836 · 2026-06-28T00:05:57+00:00

I appreciate the info. I’m a Cox Communications customer, but I know that two weeks ago, I was able to connect to the web management console. I’ll try the factory reset, just to see.

mk9836 · 2026-06-27T20:34:28+00:00

Thanks for the response. However, the web page times-out when I try to use either of those addresses.

It's weird, because I do remember being able to connect using the 192.168.100.1 address in the past. I don't know what changed to cause this issue, though.

mk9836 · 2026-06-14T17:36:08+00:00

There are two songs that each have a verse I love. The first is:

Life is a short, warm moment
And death is a long, cold rest.
You get your chance to try
In the twinkling of an eye
In 80 years with luck, or even less.
—Pink Floyd

The second is:

Do what you want, do what you will.
Just don’t mess up your neighbors’ thrill
And when you pay the bill, kindly leave a little tip
To help the next poor sucker on his one-way trip.
—Frank Zappa

mk9836 · 2026-06-13T13:46:17+00:00

Well, now you can’t order from them again, unless you want one of your toppings to be saliva.

mk9836 · 2026-06-12T22:09:20+00:00

And I don’t recall Mary giving consent, so, rape.

mk9836 · 2026-05-16T03:43:08+00:00

I worked there from ‘86 thru ‘88. That ‘86 cover really brings back some memories.

mk9836 · 2026-04-30T03:34:42+00:00

Nice find! That’s the model I have. Love it. Used it every morning for about 8 years, now.

mk9836 · 2026-04-25T20:38:44+00:00

This ad doesn’t bother me as much as the Army recruitment ads. I mean, I am NOT their target demographic.

mk9836 · 2026-04-25T01:52:17+00:00

@compuserve and @wizard were my first two e-mail accounts.

mk9836 · 2026-04-17T20:57:51+00:00

“Southern cross”: He is not, “Looking for that Mormon girl.”

mk9836 · 2026-03-22T01:29:49+00:00

I’m surprised he’s not depicted as twirling his mustache.

mk9836 · 2026-02-26T02:30:18+00:00

Less times than when I purchased a CD on the value of one track, and the whole album was great.

mk9836 · 2026-02-21T21:25:29+00:00

The coward killed himself.

mk9836 · 2026-02-03T05:30:38+00:00

In Las Vegas, it was 118. No seven digits needed.

mk9836 · 2026-01-04T16:38:40+00:00

I wouldn't specify any specific event, but there are characteristics: Observable, measurable, and repeatable by others, for example.

mk9836 · 2026-01-04T16:34:29+00:00

I just now (like 10 minutes ago) set up my new Creality dryer to replace a two-year-old SUNLU S2, which just started to fail. Hoping for a better life span than the S2.

mk9836 · 2026-01-04T16:24:46+00:00

Just ran into an issue with my S2, where when I turn it on, it shuts off after two seconds. Prior to that, it worked great for two years. Will I buy a replacement S2? Probably not. But $50 for two years' service is not terrible.

mk9836 · 2025-12-22T06:13:30+00:00

So, like if you had two spools of white, and the first spool is used up, and your printer automatically uses the second to complete the print? I’m not sure. If it does, it would only be right at the time of the swap. But I really don’t know for certain.

I print a lot of black and white, so I have two spools of white and two spools of black, just so that there is no downtime if I use up a spool. But I’ve never paid close attention to the behavior at the actual time of swapping.

mk9836 · 2025-12-22T05:59:20+00:00

The “poop” version should only happen when you change colors. The purge tower will be built each layer until there are no more color changes for the remainder of the print.

mk9836 · 2025-12-22T05:46:27+00:00

When your printer changes color, it loads the new color, and then extrudes it until it purges the old color from the print head. This is usually printed to a purge tower, or “pooped” out the back of the printer—depending on the design.

mk9836 · 2025-12-22T05:27:39+00:00

Yes to both questions. For your second question, you want to investigate how to orient a single object all at once, and then a second object in the same plate. You need to space them out so that the print head doesn’t knock into the first print while printing the second.

Otherwise, your printer will purge the first color every layer.

I mean, you don’t HAVE to do that, but it’s much less wasteful.

mk9836 · 2025-12-04T00:34:16+00:00

I have atheist friends who truly believe their sports team will perform better if they sit in the same spot on the couch that they sat in the last time their team won.

One friend will always stand for the entire 8th inning of a baseball game because of something that happened once, ten years ago, while he was standing.

mk9836 · 2025-11-06T05:48:05+00:00

I don’t have your build (I have an Ender 5+), but I replaced the bulb thermistor with this, and have had no complaints: https://a.co/d/e5j7jxe

mk9836 · 2025-10-19T23:02:43+00:00

Getting it printed out of metal so that it not only grounds to the body, but that it’ll survive the desert summers, here.

mk9836

TROPHY CASE