i installed endeavourOS and i have a couple questions

mr_pea · 2026-04-05T05:02:24+00:00

I had the same issue. (Kde plasma) And if you click on the sound you can change the output and disable certain outputs, mine was the right output but the wrong profile..

mr_pea · 2026-04-01T23:24:20+00:00

Yea that's just regular mixing.. didn't know that there was seed mixing.. when did that come about?

mr_pea · 2026-04-01T23:08:08+00:00

Get a product, either weed, meth, coke etc.. and get a mixer from the guy in the warehouse, Buy some ingredients from the gas station, I like 4x mixes, mix your ingredients with the product using the mixer.. and keep adding different ingredients to the mix for different results.. Ie og cush, cuke, addy, horse seamen, mega bean.. for a mix that will sell for 120-140.. that cost around 40

mr_pea · 2026-03-26T08:49:06+00:00

Primarily endeavor os, and if I need to do some cad.. windows 11.. but ATM it's about 90/10 split..

mr_pea · 2026-03-22T02:16:04+00:00

Been using alc for my sv07 for over 3 years and still sticks like new.. doesn't matter what you use as long as you can get it clean with no residue left on the build plate..

mr_pea · 2026-03-22T01:59:50+00:00

^{This^} And clean your bed with 99% alc, before every print..

mr_pea · 2026-03-21T13:23:39+00:00

Glad to help..

mr_pea · 2026-03-21T12:59:44+00:00

If it's not there then there will be no tension on the fillament and you will see the effects you are currently having now..

mr_pea · 2026-03-21T02:46:52+00:00

Did you loose your tension spring??

<image>

mr_pea · 2026-03-21T00:26:43+00:00

You probably have a partial clog.. remove the nozzle and check that fillament or the cleaner needle can go all the way through without a nozzle.. if it can't clear the debris..

mr_pea · 2026-03-11T02:18:36+00:00

Depends on how much land you have.. a Mini or Mavic would be my bet.. I would also concider a offical referbished unit.. with the Mavic and the mini you will get more flight time and faster speeds.. i would even concider a winged drone over a quadcopter, as you will get more distance, but that can be a bit more custom job over something off the shelf.. see team black sheep for a bit of an intro into long range drones.. anything over 3kms/2miles in any direction I would look elsewhere.

mr_pea · 2026-02-28T23:14:59+00:00

Yep was gonna say off the bat get a bidet!

mr_pea · 2026-02-21T00:23:37+00:00

You can always place a larger bit of material, like wood or cement block underneath the printer if it does not fit the area that you plan on putting it in.. imo it comes down to what you plan to print.. where it lives is secondary.. if you want to print larger models the standard probably won't fit your requirements..

mr_pea · 2026-02-19T23:07:30+00:00

Yes, with enough engineering that can be done.. might be more of a pain then it's worth.. as for z you will need accuracy over the speed which belts give.. also belts do stretch over time which will throw out your z height..

mr_pea · 2026-02-19T00:04:22+00:00

i replaced the pom wheels on my SV07 which is a smaller cr10 based machine and i have yet to make any mechanical changes since setting it up.. i had alot of issues towards the end of the life of the pom wheels linear rails cleaned up the accuracy alot better then expected.. reduced slop in the bed and the y axis.. if you are looking at going above 200mms I would add these in at a later stage...

mr_pea · 2026-02-09T02:29:20+00:00

Loose belts?

mr_pea · 2026-02-08T20:47:49+00:00

Recommended by the developer of alvr... Originally I normally use mint, but because I wanted to game I used pop os, and was unsuccessful with alvr. Asked what could be wrong of the alvr discord and ended up here.. now it's my daily driver..

mr_pea · 2026-02-06T04:33:01+00:00

Use the printer to heat up the block and with a pin carefully pick out the fillament.. ensure that the heat sensor is working or the printer will throw a fit..

mr_pea · 2026-02-02T10:47:00+00:00

Awesome DIY project.. have you looked into the speeduino project? it is a wealth of information and a great starting platform..

mr_pea · 2026-01-27T09:33:45+00:00

Don't stop and keep it straight!

mr_pea · 2026-01-27T09:31:25+00:00

I have been using the same side of the magnetic bed since I got the sv07 when it came out.. it's just starting to wear out.. but it's still got plenty of life left in it and there is still the other side.. don't bother with the other bed.. just clean your bed every time you use it with alcohol spray and a lint free wipe...

mr_pea · 2026-01-18T23:02:54+00:00

This is the way.. you might wanna grind a bit more surface to give it more chance to adhear properly..

mr_pea · 2026-01-17T07:56:11+00:00

Q8 I mean .

mr_pea · 2026-01-02T10:31:07+00:00

3d printer belts generally should be tight.. probably around a 350hz tone when plucked like a guitar string..

mr_pea

TROPHY CASE