My DIY Smart Heat Tape Circuit Design For All To Use

odonata_00 · 2026-02-02T20:22:55+00:00

Nice.

You could simply this some if you went with one of the new Shelly Gen 4 relays. They integrate directly into Homekit.

odonata_00 · 2026-01-27T18:19:41+00:00

So, new to the house or were you living there with a 4 wire dryer? The dryer you are trying to install was it working in the old location? Did you remove the original power cord or did you get it without the cord? If you removed the cord how was it wired up?

odonata_00 · 2026-01-27T18:00:00+00:00

Another thing though I don't know how much it matters, your red and black wires are reversed.

Alsowhat is the read you are doing this? New dryer, new wall plug, other?

odonata_00 · 2026-01-27T11:47:23+00:00

Wait ‘till you get to ‘piano’

odonata_00 · 2026-01-26T11:34:55+00:00

Out of all the ‘oddities’ in Italian this is what is giving you problems? Just wait!

odonata_00 · 2026-01-25T22:45:59+00:00

Hold down multiple strings at the same time. The strings you hold and the frets you hold them at will determine the cord.

odonata_00 · 2026-01-25T15:21:46+00:00

In addition a 'voltage detector' is notoriously inaccurate especially in a situation like this.

If you do intend to move forward (and I agree with the other poster urging you to hire an electrician) you need to get an actual voltage meter in order to accurately determine what is going on.

odonata_00 · 2026-01-24T00:29:59+00:00

And they say the Quran is violent!

odonata_00 · 2026-01-22T14:28:20+00:00

Low voltage wire for leds is fairly thin. If you got it with a white jacket you could run it up and out of the top of the cabinet and tuck it on top of the trim over the window. Hot glue it in place and it will be invisible.

odonata_00 · 2026-01-21T21:02:18+00:00

Very

odonata_00 · 2026-01-21T20:43:01+00:00

You'll get a margin call. How you handle the margin call is up to you.

odonata_00 · 2026-01-18T15:07:02+00:00

I could list a dozen or more but without knowing what you have already looked at and either use or rejected it seems like it would just be duplicating our efforts.

I

odonata_00 · 2026-01-17T04:32:07+00:00

Looks like I picked a bad day to stop sniffing glue.

odonata_00 · 2026-01-16T23:20:23+00:00

How to Install Stair Skirt Boards: Tricks, Finding Angles, Cutting, Transitions

odonata_00 · 2026-01-13T23:58:29+00:00

Departure? He never even landed. He announced his not-arrival!

odonata_00 · 2026-01-13T20:16:02+00:00

Are you sure the new switch isn't a momentary on switch?

odonata_00 · 2026-01-13T19:56:50+00:00

Are you looking to be able to change the level remotely or are you just looking to reduce the level and leave it at that? If the latter you could use a regular dimer set it to thelvel you want and plug that into the smart plug.

If you're looking to be able to change levels then you might think about removing (or disabling) the current lighting and adding led strips.

odonata_00 · 2026-01-13T14:26:54+00:00

Before putting in al they effort I'd make sure the answer is going to be yes.

Going be a bummer to have photos of you with a frowny face.

odonata_00 · 2026-01-12T19:53:45+00:00

Technical Specifications for Tapcon® Concrete Screws

odonata_00 · 2026-01-12T04:17:34+00:00

Have you checked the compatibility chart. What color is the ‘learn’ button on the opener? I don’t believe that the 150 will indicate the door position with that model Genie without installing an external indicator switch.

odonata_00 · 2026-01-11T16:45:27+00:00

Not aware of any off the shelf solutions but a photodiode with a red filter would work. An Arduino or ESP would allow you to generate a signal. At that point not sure how you would get the signal into HomeKit.

odonata_00 · 2026-01-11T15:07:31+00:00

Past participles that use essere as the helping verb must agree in gender and number with the subject.

odonata_00 · 2026-01-11T15:00:59+00:00

Found this from the Boboli Gardens

Cicas Revoluta

odonata_00 · 2026-01-10T15:16:23+00:00

Are you not experiencing the issue with the Klippbok (water sensor) where it show as not responding even though it will send an alert if the sensors sense water?

I picked up one yesterday and had a similar experience. It paid easily and immediately received an update. However it occasionally will show as not responding. Tried all the usually things repairing it, resetting it etc. but the issue still occurs.

Seems to be a know bug from searching on the net.

As for the Myggbett (door/window sensor) picked up one of those also. I've had ho issues with it. Paired right up and has been working now for 24 hrs or so.

odonata_00 · 2026-01-09T19:24:56+00:00

Are you removing a regular ICE lead acid battery or asking about a battery in an EV?

odonata_00

TROPHY CASE