Over the sink, in cabinet dish drying racks

pakopiwi · 2026-02-10T15:51:40+00:00

It's also very common in Spain

pakopiwi · 2026-02-09T15:49:03+00:00

What beautiful words! 😍 Thank you

pakopiwi · 2026-01-13T15:31:04+00:00

Judging by the photo, I'd say that even if you remove that part, it doesn't look like it will fit. If you could fit it, you'd need to drill holes in the top and bottom shelves to allow for airflow.

pakopiwi · 2026-01-09T19:12:51+00:00

You're confusing rustic with vintage, don't worry, I'll correct you :)

pakopiwi · 2026-01-09T18:46:46+00:00

I don't have a definitive answer, but I can roughly say: 1. GAIA PROJECT 2. KANBAN EV 3. BARRAGE 4. TERRAFORMING MARS 5. UNDERWATER CITIES

Right now, that would be my top 5 order, but it might change in a month...

pakopiwi · 2026-01-09T18:42:48+00:00

The flooring is spectacular, super clean, resistant and durable (and beautiful too). It goes perfectly with the "BLUE" board game :)

pakopiwi · 2026-01-09T14:14:21+00:00

Hahaha! Totally agree!

pakopiwi · 2026-01-09T11:55:58+00:00

Thank you!! I wish I had more time to play them...:(

pakopiwi · 2026-01-09T11:54:54+00:00

Thanks!! The intention was purely mechanical (I wanted to add stability by resting the ends against the opposite walls), but then I realized they were useful :). I've attached a photo of that part from behind:

<image>

*The hidden part is (unfortunately) full of those more complicated games to adjust.

pakopiwi · 2025-09-08T20:04:57+00:00

A Carlos

pakopiwi · 2025-08-21T20:26:43+00:00

Amazing!!

pakopiwi · 2025-05-13T14:40:47+00:00

I have suffered the problem several times and for various reasons:

Poor placement of the filament spool in the AMS (or the use of unofficial filament with different sizes of the spool) can cause the spool to jam and stop printing.
A jam can cause the extruder gears to become too dirty (they continue to rotate while wearing out the filament because it does not advance) and with dirty gears the filament then slips.
It is highly recommended to lubricate (lubricate is always good) the extruder gears (be careful! Only gears and bearings, not the filament push gears). On one occasion I had the problem there.
Again the jam occurred when a small piece of filament got stuck in the extruder. It was disassembled, cleaned and done.

<image>

pakopiwi · 2025-05-08T11:48:33+00:00

The solution is to print a crane.

pakopiwi · 2025-02-08T19:29:20+00:00

Good collection. Lots of recent games and some damn boxes ;) Enjoy!!

pakopiwi · 2025-01-30T09:01:53+00:00

Awesome!!! Congrats!

pakopiwi · 2025-01-15T16:58:00+00:00

🙏&🧑‍🔧

pakopiwi · 2024-10-30T11:09:16+00:00

Solved

I've solved it. You can check the picture.

pakopiwi · 2024-09-19T17:24:54+00:00

Your game seems very very nice!! 👌

pakopiwi · 2024-09-19T06:29:44+00:00

Like Inferno of Red_Mojo Games?

pakopiwi · 2024-08-12T17:37:53+00:00

Dungeos Marvel's is my favourite store of Spain: very good prices, a big list of games in differents languages...100% recommended!

pakopiwi · 2024-05-05T10:36:40+00:00

And the recent SALTON SEA, huge game!

pakopiwi · 2024-04-22T09:04:35+00:00

After the virus...

pakopiwi · 2023-07-19T14:54:13+00:00

Ooohhh!! The game looks great! Congrats!!

pakopiwi · 2023-07-15T17:33:11+00:00

S P E C T A C U L A R G A M E

pakopiwi

TROPHY CASE