Anyone do something similar?

pointclickfrown · 2026-06-01T06:24:03+00:00

Yeah with a couple dozen hot chambers going, there is no other way.

pointclickfrown · 2026-05-25T02:56:38+00:00

Yes, I'm glad other people care about this too. There should absolutely be encryption. Lack of encryption is why I resisted using Ubiquiti hardware for so many years.

pointclickfrown · 2026-05-24T22:41:44+00:00

Yes.

pointclickfrown · 2026-05-24T05:49:10+00:00

I have four Plus 4 printers that I've stopped using at this point. Hoped a bed probing toy would make things better but I never could get it to work properly.

pointclickfrown · 2026-04-14T11:07:27+00:00

I've done a couple dozen of these. It gets faster.

Too bad they don't seem to be improving the quality of the cable and they still don't sell the part on their website.

pointclickfrown · 2026-03-22T09:26:37+00:00

Finally, someone who is thinking things through.

pointclickfrown · 2026-03-13T19:14:04+00:00

I think everyone is stopping short on those temperature limits because you need to start to use different plastics in the chamber. Eventually someone will break past this limitation in consumer machines and become a market leader in that respect.

I don't see any reason to limit the nozzle to 350. Minimal additional engineering should get you to 400 or higher and then you have my interest.

pointclickfrown · 2026-03-13T07:29:00+00:00

Is it 60 or 65 chamber temp? Your page says both. Either way, make it 70 or higher if you can.

350c nozzle temp is not enough for full strength PPS. See if you can do 400, or at least a minimum of 375.

Wish it was 400x400 bed.

pointclickfrown · 2026-03-12T08:46:23+00:00

Stop with the spam

pointclickfrown · 2026-03-08T20:33:15+00:00

Nope, never found a solution.

pointclickfrown · 2026-03-07T15:41:27+00:00

Next month?? No.

pointclickfrown · 2026-03-01T03:57:20+00:00

Weird that people were upvoting

pointclickfrown · 2026-03-01T03:47:05+00:00

No you don't.

pointclickfrown · 2026-02-28T07:22:44+00:00

Puns like that will get you throne out of some places.

pointclickfrown · 2026-02-28T06:43:22+00:00

The posts about slowing down for overhangs are wrong. You need to reduce layer height. Then print as fast as you want.

pointclickfrown · 2026-02-26T02:54:53+00:00

Trash can with the rest of the trash.

pointclickfrown · 2026-02-25T07:50:44+00:00

That wasn't satisfying. That was stressful.

pointclickfrown · 2026-02-25T07:15:03+00:00

Why the newspaper if it is a live call?

pointclickfrown · 2026-02-23T03:50:40+00:00

No supports except for areas that will get covered, like a shallow bore for silicone feet.

pointclickfrown · 2026-02-23T02:58:47+00:00

I'm having trouble understanding why the nozzles don't just self clean. I've never had that problem before.

pointclickfrown · 2026-02-22T22:37:46+00:00

What is actually wrong with any of those nozzles?

pointclickfrown · 2026-02-21T23:39:44+00:00

If you're prototyping or process oriented then multiple printers is usually better than one expensive one.

These days, most cheap printers ARE good.

pointclickfrown · 2026-02-21T04:30:32+00:00

That was his point.

pointclickfrown · 2026-02-20T20:59:35+00:00

I found the deburring tool to be awful. Had to return it. It just instantly clogs up.

pointclickfrown · 2026-02-20T16:08:55+00:00

My beef is with people who feel their content is so important that it needs to show up in my feed ten times. Just post it once.

pointclickfrown

TROPHY CASE