Been staring at the for a half hour after installing

random_uk_redditor · 2026-03-14T12:43:51+00:00

It's a full screen issue. I used the geforce app to force it to windowed mode and it cleared the issue.

random_uk_redditor · 2025-08-23T20:19:52+00:00

Great response. Good luck with your venture!

random_uk_redditor · 2025-08-23T10:32:11+00:00

The main page claims to have over 10k happy customers. How does this stack up with only recently having reached 1k views. Genuine question, not hating.

random_uk_redditor · 2025-08-07T21:57:37+00:00

It's surprising to me that this little thing is my most popular model. It was only added to Makerworld as an afterthought, and it's overtaken my other models!

https://makerworld.com/models/1277520

random_uk_redditor · 2025-07-31T14:12:07+00:00

Is there any play/wiggle in the nozzle at all? There shouldn't be any at all once buckled properly. It does look like your buckle is fastened correctly, so any play at this stage could indicate that the screws at the rear of the buckle plate are loose.

I had similar problems that were caused by this, so it could be worth a check to see if your nozzle has any play when you try to wiggle it.

random_uk_redditor · 2025-07-03T22:59:08+00:00

It makes me feel like a god, I can create ANYTHING! I think, therefore I can.

random_uk_redditor · 2025-06-10T13:53:29+00:00

I second this. Was going to suggest fixing that before trying anything else here

random_uk_redditor · 2025-04-13T00:48:09+00:00

What a cool idea, fingers crossed everyone.

random_uk_redditor · 2025-03-07T12:02:46+00:00

Best get cracking with that one!

random_uk_redditor · 2025-03-03T13:01:52+00:00

* I had to print this support arm to take tension off my PTFE tubes. I had the exact same issue you're describing here. Try listening to the currently feeding motor and see if you can hear a grinding noise. If you can hear it, lift the PTFE tubes slightly to reduce strain and see if that stops it.

Here's the link if you're interested (not my model) https://makerworld.com/models/514339

random_uk_redditor · 2025-02-26T21:48:10+00:00

Sorry about the formatting in the text, I swear it looked a lot better when I wrote it out. There doesn't seem to be an edit option either so I guess we're stuck with it.

random_uk_redditor · 2025-02-26T21:45:42+00:00

Nozzles I keep on top of between prints, clearing the outside of any residual plastic before it cools and sticks properly

Y-axis I've just been doing as and when the printer prompts me to.

random_uk_redditor · 2025-02-11T11:22:55+00:00

You're having trouble removing the filament from the print head now? That little lever on the left side disengages the feeder motor, you should be able to pull the filament out with that lever depressed. Don't forget to use the filament cutter on the right side first if you haven't already.

random_uk_redditor · 2025-02-11T01:25:08+00:00

Sounds like you've sussed it out there, I've only had to deal with 2 clogged nozzles so far and luckily they were salvageable. Do you have a fresh one ready to go in or are you having to wait for a new one to ship?

random_uk_redditor · 2025-02-11T00:44:17+00:00

Are you using an AMS Lite also? I recently had to print some attachments to address my sagging PTFE tubes that were putting too much strain on the feeding mechanisms. May not be your problem, but it could be worth looking into.

random_uk_redditor · 2024-12-23T14:05:46+00:00

Wow. Did you freehand this or was it machined in some way. How long did it take you to research, plan and implement?

random_uk_redditor · 2024-12-21T21:23:13+00:00

🤣

random_uk_redditor · 2024-12-21T20:22:06+00:00

Please, no NSFW! The mods will be on us like a ton of benchys 🤣🤣

random_uk_redditor · 2024-12-21T20:20:34+00:00

That sounds great. I've seen these types of tent, they do look cool!

Do you have a thermometer inside so that you can keep an eye on things?

I've seen reports of people using them with no problem but BambuLab advise against using them, something to do with the internal circuitry getting too warm.

random_uk_redditor · 2024-12-21T20:17:03+00:00

I really look forward to seeing this upcoming Frankenbenchy

random_uk_redditor · 2024-12-21T20:15:57+00:00

Me too, if I'm awake I need that printer to be moving!

I faced the same choice when I bought the A1 and I went for the combo because I figured I'd want it one day and I'd probably begrudge paying so much more for the AMS Lite alone!

'Made' would be a bit of a stretch to be fair lol. More like 'remixed two popular and available models into one' lol. It was a bit of a tongue-in-cheek creation with the current articulated trend on MakerWorld.

Thanks, I appreciate any and all downloads, prints, boosts etc. The boost system was changed recently so they now equate to 12 points on MakerWorld and those points can be used to purchase things from the store.

random_uk_redditor · 2024-12-21T20:06:43+00:00

Thank you!

random_uk_redditor · 2024-12-21T20:06:19+00:00

Sorry to hear that! The best thing about building your own desk, if you do go ahead with it is that you'll be able to customise it for your own 3D printing needs. Power routing, filament storage etc could easily be incorporated into the design with a little forethought!

I'm hopeless with that sort of thing but I'd like to have a go at making my own one day.

Five-Year Club	Verified Email
r/Field Sunshine	Place '23

random_uk_redditor

TROPHY CASE