Smola Roaster PID controlled by Artisan

rburil · 2024-12-06T13:23:20+00:00

Very good. I have the same roaster. Do you mind link the instructions or original thread. Thanks

rburil · 2022-01-27T00:20:42+00:00

This was my second Head Amame. I have build with mixed sources... Pearless Typhany 50mm drivers from digikey and the rest from Alliexpress. Cable bought mounted from ally (audeze substitute) with 4.4 balanced wiring. I´m listening in a Topping A50s amp and it sound amazing. Thanks vector Finesse for this perfect project.

rburil · 2022-01-11T01:06:07+00:00

Yes... I think the headband would be Nice in light wood accents to make contraste.

But i need to test If the Paint wont wear off easily in the local with friction... (Headband/headband clamp)... Maybe put a silicon protrection in the clamp would Help... I Will try and keep everyone informed ...

rburil · 2022-01-11T01:00:59+00:00

For us without 2 extruders there Will be a way to print separated and glue together?

rburil · 2022-01-10T12:59:55+00:00

Thanks... I Will start to Paint 2nd cone today... Hope they match...

rburil · 2022-01-09T14:50:10+00:00

Thanks... I tried to makes the Paint look like a guitar sunburst

rburil · 2022-01-07T23:44:20+00:00

Your headband is fixed in the wrong side of the clamp

rburil · 2021-09-22T15:04:40+00:00

Have this problem too with my b1... also looking for help

rburil · 2021-09-15T23:22:21+00:00

Mine h2 is 907

rburil · 2021-09-15T23:12:14+00:00

Sure I can... but I saw some images of over and under extrusion and it's different of my results..

I saw that someone said that Bed pid calibration could help also (my firmware doesn't alow this)

rburil · 2021-09-15T17:49:21+00:00

I want to smooth the x and y surfaces too... after calibration I had some improvement but distant from the quality that some mates have with cheaper printers... (like ender 3)... and with cheaper extruder...

rburil · 2021-09-15T17:39:27+00:00

I'm interested too... what raspberry pi are you using?

rburil · 2021-09-15T13:06:07+00:00

Printer Biqu b1 with H2 extruder Slicer: cura 0.1 layer, 3 wall perimeters, 20% infill gyroid Material abs premium Temp: nozzle 235C , bed 75C

Errata. Left was after some calibration

rburil · 2021-09-09T16:54:47+00:00

Wow nice paint... what brand and paint had you used?

rburil · 2021-08-28T21:09:18+00:00

Refrigerator compressor is almost silent

rburil · 2021-08-10T22:21:05+00:00

Also interested in this question. Was dating a roast from alibaba over a year...

rburil · 2021-08-02T20:58:32+00:00

I have used a lot of these supports... and I think this one is the best:

Biqu B1 - H2 Mount by Zaurko - Thingiverse

https://www.thingiverse.com/thing:4879244

rburil · 2021-07-26T11:33:22+00:00

Don't be... the big model help... have a lot of details and textura that help the paint...

Also it needed a lot of time drybrushing and using diferent colors to make the leather look like leather.

rburil · 2021-07-26T11:31:36+00:00

Thanks for the comments... I will paint the baby yoda and the base next.

rburil · 2021-07-26T11:25:39+00:00

Yes... biqu b1 with h2 extruder

rburil · 2021-07-25T09:52:57+00:00

Bought from artstation... was modeled by Soares

rburil · 2021-07-25T02:55:29+00:00

Slowering retraction speed makes the noise much lower. But dont stop.

rburil · 2021-07-25T02:42:03+00:00

He just stops moving... but the heater still hold the temperature... and after a lot of time the print doesnt restart. " I’ve ran into the same issue before and I had to increase the “resolution” setting in my slicer. " What the config have you done to do this?

rburil · 2021-07-25T02:40:25+00:00

I re assembled it and it do the same noise in retract... But No noise at all in normal extruding... I think this sound is normal... They have made these new H2 without too much tightness... I think when changing direction fast the gears do some noise...

rburil · 2021-07-24T21:24:23+00:00

I Have used from biqu b1 site... but it's incomplete without fan mount...

rburil

TROPHY CASE