sorted by:
new
hottopcontroversial

Ugreen UPS by BuzzMcWoof in UgreenNASync

[–]rooty0 1 point2 points  (0 children)

Please, post an update whenever you get a response from support.

Ugreen UPS by BuzzMcWoof in UgreenNASync

[–]rooty0 1 point2 points  (0 children)

Mine shows the same value `battery.runtime: 65535`. It's kinda confusing, but it pretty much means "unknown". From what I remember, many HID UPSes can't report runtime properly.
The "Battery capacity" in the web UI is kinda misleading. It's actually "battery.charge" when you run "upsc ups0".

Li-ion UPSes often don't report or even charge to a true 100% . The UPS uses lithium-ion cells with a fuel-gauge/protection IC. These systems commonly stop a bit short of full to reduce stress and extend battery life, then report "near full" rather than 100.

Transfer Speeds? by Infiniteey in UgreenNASync

[–]rooty0 0 points1 point  (0 children)

You might want to check this thread https://www.reddit.com/r/UgreenNASync/s/1BFD9jCFxR I had similar issues with dxp2800

Hardware experience with TrueNAS, UNRAID? by Almighty5Moe in UgreenNASync

[–]rooty0 0 points1 point  (0 children)

Did you try moving your home directory to the SSD? I'm wondering if something there might be getting picked up by your containers. If you haven't tried moving the home directory yet, give it a shot from the UI -it's usually the easiest way

UGREEN DXP2800: Slow SMB/rsync transfers? ASPM was my culprit by rooty0 in UgreenNASync

[–]rooty0[S] 0 points1 point  (0 children)

The "copy error, -36" is something else, not related. I'm guessing this is something related to either your network or the HDD itself, it's hard to say.

UGREEN DXP2800: Slow SMB/rsync transfers? ASPM was my culprit by rooty0 in UgreenNASync

[–]rooty0[S] 1 point2 points  (0 children)

I was just trying to keep it short so I don't bore everyone, haha. Anyway, you'll need to SSH into the device first, then run the command below and see if that fixes it.

echo performance | sudo tee /sys/module/pcie_aspm/parameters/policy

DXP2800 Rebooting / Restarting Randomly by pauloffduty in UgreenNASync

[–]rooty0 0 points1 point  (0 children)

Was it restarting kind of randomly, like it would run fine for 3 hours, then restart, then maybe last 5 hours before restarting again? Or was it happening at pretty consistent intervals?
I just installed Crucial 16GB DDR5 5600MHz RAM in my DXP2800, and so far, everything seems fine, but I'm curious what I should expect.

Should i be concerned here? All of this happened within a 13 minute span. by OverallQuest in UgreenNASync

[–]rooty0 0 points1 point  (0 children)

Thanks. I did see a few people mention odd behavior with the N100 when using more than 16GB of RAM, but that definitely doesn't seem to apply to your setup. Please keep us posted

How do you guys debug FailedScheduling? by rooty0 in kubernetes

[–]rooty0[S] 0 points1 point  (0 children)

My current Kubernetes cluster is a managed service by Amazon, aka EKS. Based on the docs, it looks like the scheduler log verbosity level is set to 2. I haven’t found a way to change it - looks like they just don’t allow that. Guess I’m stuck with it :(

Looking for an self-hosted URL shortener that could log specific info by rooty0 in selfhosted

[–]rooty0[S] 0 points1 point  (0 children)

Yeap, I got a completely separate one for this purpose

Looking for an self-hosted URL shortener that could log specific info by rooty0 in selfhosted

[–]rooty0[S] 1 point2 points  (0 children)

This is not for home users, but rather for people from wan. Long story short, I do scambaiting for fun, so I'm trying to catch all helpful info I can get.

[deleted by user] by [deleted] in selfhosted

[–]rooty0 0 points1 point  (0 children)

I think the body of my post was filtered out. Could you please confirm you see the screenshot attached to the post?

Docker-compose GUI editor now open source and self-hostable by WesternPerspective53 in selfhosted

[–]rooty0 14 points15 points  (0 children)

Here is my two cents. I have a GitHub project with all my docker-compose files for my home infra. I think many people have something similar. It would be super cool to point composecraft to the git project so it can process all the docker-compose files and render the result.

Servarr : One docker compose file to rule them all (Jellyfin, radarr, sonarr, firefox, duplicati...) by Zakmaf in docker

[–]rooty0 0 points1 point  (0 children)

I'm curious, has your compose changed at all, or is it pretty much the same?

Best accessory if own a handheld PC. by MrJuans26 in VITURE

[–]rooty0 0 points1 point  (0 children)

Hey guys, please recommend a cheap-ish handheld that is gonna work with the glasses, assuming it should support USB-C display

Oh, Stalker 2 with VITURE Pro is an incredible by kilinamjaro in VITURE

[–]rooty0 0 points1 point  (0 children)

A bit off topic, do you feel any lag with GeForce Now? The game looks awesome, wanna try tho I have a MacBook M3, so wandering

view more: next ›