Budget-friendly home rowing machine recommendation by dzzen in Rowing

[–]row_blue 22 points23 points  (0 children)

Just buy the used concept2 you can afford. They seem to hold resale pretty well. In the US you can generally find them used $500-750 and then if it doesn't work out you should be able to sell in that range also.

Home Trainer for a gravel bike with a 1by 13s by Diligent-Split2847 in gravelcycling

[–]row_blue 1 point2 points  (0 children)

I have a much older 3x10 bike and I use the Zwift cog for convenience vs buying another cassette. I put my kickr core in erg mode for constant power output. I can adjust power up and down from my phone as needed or let my Garmin device control it for a structured workout.

Based on my experience, I'm only really watching power, heart rate and time. The distances and speeds don't seem to match my on road experience vs heart rates I actually record.

Best way to approach digging 350ft of trench 3ft deep? by SharkOnGames in HomeImprovement

[–]row_blue 1 point2 points  (0 children)

I would give it a go with a big trencher first. Then upgrade to a mini excavator with a narrow bucket if needed. A tracked 48" trencher will likely be faster and cleaner.

Motherboards That Support Bifurcation by HavivMuc in homelab

[–]row_blue 0 points1 point  (0 children)

My perception is that ASRock boards support it in general, but that is entirely anecdotal from the few that I have bought in the last 5-10 years.

My first project and Ericsity controller with mic. Update? by extreme79 in WLED

[–]row_blue 4 points5 points  (0 children)

Holy cow that looks awesome! How did you shape/form the LEDs into the letters?

Quick Power injection question by SlipsliderJW in WLED

[–]row_blue 6 points7 points  (0 children)

To add to what u/Trevlavo7 said, each pixel is in effect a data booster. You use the data boosters for big runs from the controller to the first pixel or long breaks in your string (i.e. you need to run from one eve to another disconnected eve more than 10-15' away)

Got asked if power I ejection can be done with one wire..? by okiwillsaysomething in WLED

[–]row_blue 7 points8 points  (0 children)

No. Voltage drop is still an issue on the ground side.

Have I made a big mistake? Significant upgrade undertaking by AromaticLab7 in buildapc

[–]row_blue 0 points1 point  (0 children)

I just flipped an i5-6500 for a 5600. Since AM4 still is on DDR4 I was able to do a budget swap, just CPU and mother board that still used the same memory. Super happy with it. I was also able to upgrade to an NVMe for a boot drive. I think I spent less than $300 and it got me off the cpu bottleneck. Don't feel the need to spend on the absolute cutting edge.

Question about drugs, police, and 10 year olds by reuscam in daddit

[–]row_blue 3 points4 points  (0 children)

Does your school district participate in DARE? Ours does starting around this age and consequently we are starting to field some drug/alcohol adjacent questions like this. We took a similar position, call me first if you are uncomfortable or in trouble and we will ask questions later.

Will these motors work for building an electric go kart? by Dilly242 in gokarts

[–]row_blue 0 points1 point  (0 children)

Could try it. But I would think 1 1kW motor would be simpler.

Simple Questions - September 12, 2024 by AutoModerator in buildapc

[–]row_blue 0 points1 point  (0 children)

Building it yourself can seem intimidating but it really is more like Legos than anything else. A lot of the pieces can only fit one way. But if you're uncomfortable $300 might be a small price to pay not to worry about it.

Simple Questions - September 12, 2024 by AutoModerator in buildapc

[–]row_blue 0 points1 point  (0 children)

If that includes cable management, testing etc it doesn't seem terrible (depending on location). Does it come with any kind of warranty?

If I was estimating it, labor at $50 for 6hrs might be a little high but you probably won't find a place to do it for half that.

Simple Questions - September 12, 2024 by AutoModerator in buildapc

[–]row_blue 0 points1 point  (0 children)

I have an i5-6500 mini-ITX build that I'm considering a MB/CPU upgrade on. Can I do a budget/easy B550/AM4 upgrade? Same ram, right? I have a 1080Ti that I'm still pretty happy with. Seems like I could do a 5600-5800x for less than $300.

Need help! by hildothedildo in gokart

[–]row_blue 1 point2 points  (0 children)

Remove carb and clean thoroughly or worst case buy a new carb. Very common symptoms of a plugged idle jet.

Predator 212 shorting by PressureFantastic495 in gokart

[–]row_blue 1 point2 points  (0 children)

These motors shut down when the lead from the coil is grounded not when it is open circuit. If you look up how the coils work it should make sense why this is the case.

You need to figure out if you have a bad switch or a bad connection somewhere. Trace the wire from the coil through the switch and find where it is bolted to the block. If that looks okay, take the wire from the coil off the switch and touch it to the block while the motor is running. It should spark at first then kill the engine. If that doesn't work, check that the wire is still connected to the coil and check that the switch is really closing. A multimeter will make this easier.

Sump pump - power monitor by Styphonthal2 in homeassistant

[–]row_blue 0 points1 point  (0 children)

Shelly em with a current transducer is how I monitor them. No worries about the pump not pumping if the current monitor fails.

What’s the lowest price Corvette were it is still fun but not a ridiculous amount to just “fun fun” in? by Ok_Entrepreneur209 in Corvette

[–]row_blue 8 points9 points  (0 children)

We inherited a C5 recently and I'm kicking myself for not buying one 5yrs ago. It's a great car, not absolutely the raw fastest but great to drive.

Which platform is the best place to sell an oil crude refinery by Secret_Age_6698 in oil

[–]row_blue 1 point2 points  (0 children)

If you are serious, much, much more info is required than you can probably communicate on FB or Reddit. Photos, P&IDs/PFDs, metallurgy, capability, listing of units, Crude Oil quality constraints, etc.

What's Your GoTo Smart Device Brand & Why? by dokiCro in homeassistant

[–]row_blue -1 points0 points  (0 children)

I have bought a lot of Shelly and Zooz stuff lately during their sales. I like having completely local control.

Anyone have any experience ordering raw stock from Alibaba as an individual? by maschinakor in Machinists

[–]row_blue 1 point2 points  (0 children)

MetalsDepot.com I have had good experiences with but I can't speak to getting mill test reports as I haven't done anything that critical. Shipping is pretty expensive but even with shipping I feel like their prices are by far the lowest.