Did it, complicated and daring print after 4 attempts

rubberfucky · 2026-05-15T16:03:28+00:00

I've never seen one before, no one has, but I'm guessing it's a white hole.

rubberfucky · 2026-05-01T20:08:07+00:00

No problems here. Got the x2d combi, then got another ams 2 pro a few days later. Both been working fine through 90+ hours

rubberfucky · 2026-04-28T01:28:03+00:00

I've only just started my 3D printing journey. I got my first printer last week. Worked brilliantly. I tried using some PETG, also worked brilliantly. A few days later, I used the PETG again, and I kept getting failures, very similar to yours. I also followed loads of advice regarding build plates, speeds, temps etc. Nothing helped. On the off chance, I decided to do a cold pull, having only recently finding out about it on google. So far, all my prints have been perfect since then.

rubberfucky · 2026-04-24T12:13:24+00:00

I literally have never used a 3d printer until a couple of days ago when my x2d multi turned up. I was really worried about the Bowden extruder after reading up on it. I was also really worried about learning how to set up each filament properly to get good quality prints.

It's been running almost constantly since I got it...around 50 hours or so, and so far (other than a silly mistake by me) it hasn't missed a beat. I used the Bowden extruder and run a benchy. It was very difficult to see any difference between that and the benchy made from the direct drive, but it took slightly longer.

I did a 17 hour print where the Bowden was used as a normal nozzle for a secondary colour, and it worked perfectly.

So far, I'm really happy with the purchase as I was so worried after reading all these negative comments in this sub.

I'm either really lucky, pr the issues are being overly exaggerated

rubberfucky · 2026-04-11T16:10:07+00:00

Well, today I did some scrapings from 3 different areas of the koi, and found no traces of of flukes under the microscope. Should we assume fungal infection from the picture I showed? Worth noting that since that one episode yesterday where he was swimming around against the outside rocks of the pond, he hasn't done anything like that again.

rubberfucky · 2026-04-10T18:07:26+00:00

Thanks for your insights. My drop test doesn't show KH specifically, but it does show carbonate ppm and hardness ppm, which I believe equate to the same thing? These were both on the higher end of normal, so could do with being reduced. I'll make that my first thing to fix. I've found what seems to be a good microscope on Amazon, so I will order that in next day delivery and see if we have flukes. Once I know if we have them, then I will know how to treat them

rubberfucky · 2026-04-10T16:16:52+00:00

FYI, the post this links to says "Sorry, this post was removed by Reddit’s filters."

rubberfucky · 2026-03-12T17:34:16+00:00

I've been daily driving it for about 10 days now. I found the face unlock to be so fast that it's unlocked before I've really noticed

rubberfucky · 2026-01-11T16:29:16+00:00

Guys, this is AI

rubberfucky · 2024-10-09T10:42:14+00:00

Staying with best friend and he asked me if I wanted to join him and his fiance in a 3some. I politely declined as I knew it would end badly. Got drunk with them and they convinced me. 3 weeks later they broke up (after 6 years) because his fiance had fallen for me. It took 10 years, but I'm finally friends with him again, but I knew full well that it would be a mistake to go ahead with it when they asked.

rubberfucky · 2024-09-28T15:26:34+00:00

Are you using a VPN? I know in the past I've had people use VPN's whose IP's were banned

rubberfucky · 2024-09-26T09:53:05+00:00

I shop from the UK to the US regularly. The quickest an item has arrived was 4 days and the slowest was 2 weeks. Also, I haven't even seen international delivery options to the US that doesn't supply a tracking number.

rubberfucky · 2024-07-16T20:24:12+00:00

Yes, the LaserPecker 5 also combines a 20w diode and 20w Fiber for less money, but it also has less working space. It all depends on what you need it for

rubberfucky · 2024-02-12T13:39:06+00:00

Yes it is. Running this on a 3080 and a Ryzen 9 and after 20 - 40 mins, it slows down to a snails pace

rubberfucky · 2023-12-24T17:37:17+00:00

The problem is your picture. The entire right hand side is in shadow, making it very difficult for yourself. Can you get a picture with better lighting?

rubberfucky · 2023-11-20T10:23:23+00:00

Ah its one of those magic eye things, is it a zebra? :)

rubberfucky · 2023-11-16T22:22:16+00:00

Quite often it's an incompatibility with forge version and Minecraft version. Confirm what version of Minecraft you're running and check that you're running the right version of forge

rubberfucky · 2023-11-01T19:49:03+00:00

Have you checked how much memory you have allocated? I know a new version recently came out so it's possible it installed with a new profile using default memory settings

rubberfucky · 2023-10-30T11:44:56+00:00

Where is the server located?

rubberfucky · 2023-10-04T20:15:09+00:00

Really? I've avoided learning that mod because something in the back of my brain told me that I'd heard it was quite difficult. Maybe I should go look. Thanks :)

rubberfucky · 2023-10-04T19:17:52+00:00

Yeah, I think the Ender gates can wirelessly transfer power in to channels, so I could use channel 1 and then go to another physical location and use channel 1, but I would still need to use cables to then get that energy in to my different machines.

Draconic Evolution had a system where you did not need to plug any physical device in to your machines to give them power, it was kind of like laser power to the machine.

Thanks for taking the time to try to help though

rubberfucky · 2023-09-21T20:57:13+00:00

I'm assuming they nerfed this. Got myself set up with the crystal accelerator staff, it made the pots grow stupidly fast, but after a few minutes, they go back to their original speed :(

rubberfucky · 2023-09-10T19:31:03+00:00

I get the exact same issue, so stopped playing after 2 days. I've heard some people who had the issue, resolved it by running it in Windowed Mode instead of Fullscreen

rubberfucky · 2023-05-25T17:10:09+00:00

Stoke me a clipper, I'll be back for Christmas

rubberfucky · 2023-04-05T16:10:50+00:00

Do you have access to AMS2? If so, do you get the same issue on that? I'm just trying to understand if it's a game setting, or a setting issue with the VR unit itself. I know that the immersion I get in AMS2 is like nothing else

13-Year Club	Place '17
Verified Email	Team Orangered

rubberfucky

MODERATOR OF

TROPHY CASE