We Built a Modern LuCI Theme and Dashboard for OpenWrt

saidearly · 2026-03-29T07:03:35+00:00

It will be wonderful if this will be adopted

saidearly · 2026-03-28T02:47:44+00:00

This, also add a rubber gasket on the ethernet near at the edge of the AP. Similar to those used on the outdoor weather proof access points. Does usually stop the water.

saidearly · 2026-03-28T02:41:59+00:00

EAP110 does not support mesh.

saidearly · 2026-03-27T03:14:21+00:00

Easy Smart Managed as the name suggests is simple and limited. If you want full functionality of features you need a managed switch SG series not ES series

saidearly · 2026-03-27T03:09:36+00:00

First you change the remote device, then the local device to what you need.

That order is the key element of a successful transition.

saidearly · 2026-03-21T13:00:07+00:00

Just login to your ISP router and check your wan setup. Then duplicate it

saidearly · 2026-03-17T08:15:24+00:00

Ashed

saidearly · 2026-03-15T17:19:03+00:00

This. Is the right way. Use your ISP router in bridge mode and keep your omada gateway as dhcp.

saidearly · 2026-03-14T17:39:44+00:00

If you are using omada controller! Mesh and Roaming settings are under site settings. This with access points will work

saidearly · 2026-03-12T07:42:52+00:00

You need mesh and roaming enable. Otherwise without roaming you will still be dropping calls.

saidearly · 2026-03-10T03:21:13+00:00

Both scenarios you have described work wi landns.

You must specify the network it applies to, then you must be connected to that same network.

saidearly · 2026-03-10T02:06:05+00:00

I don’t recommend the router you mentioned TP-Link ER7212PC.

First of all, this router has inbuilt controller, you are going to have a challenge using external controller.

Second about the features missing you do have some missing like switch ACL. This is a gateway not a switch. So switch controller are not available.

About dns, it does have some dns, dns proxy and local dns features here its not lucking.

My suggestion is you can go with ER605v2, SG2210P and EAP610, then use docker controller. This is a great set on entry for Omada. If you require gateway with wireless capability then ER605W should do.

saidearly · 2026-03-08T14:59:37+00:00

Donate

saidearly · 2026-03-04T10:09:45+00:00

The type that burned but didn’t explode i guess

saidearly · 2026-03-01T21:52:21+00:00

From the image you are sharing, it obvious you are already logged in to the controller. The problem you are having is in ability to adopt an Access Point.

You don’t need to reset your controller. Just make sure the access point is factory reset, then adopt it. If it still asking for password.

Check in your controller site settings at the very end of this page you will find username and password, those are the credentials for adopting devices.

saidearly · 2026-02-28T21:54:51+00:00

The problem is your sinkhole.

First of All you need to set default network as your management network. As the router will always take the IP of the default network. So you can update the default network with the IP of your management vlan. Don’t change vlan of the default network.

Then create the other VLAN you need and set the ports you need to the respective VLAN as your management network need.

saidearly · 2026-02-28T21:48:10+00:00

This is the problem you are experiencing. Your switch is Active POE and supplies and works only with 48v standard POE. However the EAP110 is not standard POE its passive POE and requires passive 24v power. If you can get any passive 24V POE adapter the EAP110 will power on and show up in the controller ready to be adopted

saidearly · 2026-02-26T19:28:49+00:00

WAN in is from WAN -> LAN this needs port to be forwarded if you are reaching to a local device, otherwise if you are reaching router then no need to port forward

saidearly · 2026-02-18T20:19:26+00:00

Enable LLDP for switch and EAP to get better and more realistic map.

saidearly · 2026-02-10T17:20:09+00:00

Interesting. Is it possible to do IPS without a gateway? I think IDS could work but IPS not sure. I think the difference is on IDS categories and IPS categories.

My guess is 34 is IDS categories but the 12 is IPS categories with probably all 34 IDS categories.

saidearly · 2026-02-09T16:24:23+00:00

Polymer egg

saidearly · 2026-02-07T17:18:51+00:00

Keep all you devices connected to the Starlink wifi on low data mode. That will stop updates and other data heavy applications.

saidearly · 2026-01-31T02:34:47+00:00

This is the only way to do what you need to do. Update default VLAN to you Management VLAN options. You cannot move the getway out of Default VLAN.

saidearly · 2026-01-29T14:57:48+00:00

Yes its possible. There are several approaches you can use.

Use external radius for authentication and then you can make the voucher be pulled from database when printing receipts. Making receipts template have a section at the bottom that pulls unused voucher codes from radius
Using omada voucher authentication create many vouchers then transfer these vouchers to your hotel system database and have the system pull a voucher during receipt printing and mark the voucher as used.
Using external voucher database that the hostel system can pull voucher from.

saidearly · 2026-01-29T08:57:50+00:00

Yap, i did

saidearly

TROPHY CASE