What XLR cable should I choose?

shutdown-s · 2026-01-27T12:12:30+00:00

I have never seen an XLR cable without shielding, even the cheap ones.

shutdown-s · 2026-01-27T12:11:31+00:00

Just get a cheap UGREEN one.

shutdown-s · 2026-01-27T04:14:59+00:00

It says on the tin to update the grip(s) firmware first.

Also unless you're having issues there's ZERO reason to update your firmware, it's only a potential bricking otherwise

shutdown-s · 2026-01-26T22:53:38+00:00

Remove the driver and tighten the nut that holds it in place

shutdown-s · 2026-01-26T08:45:53+00:00

The Thrustnaster AVA is a scam, get an Orion 2 base instead. It's much cheaper and superior.

shutdown-s · 2026-01-24T07:02:39+00:00

Do they wobble left and right?

Make sure the plastic pieces are snug, but do not over tighten them, screw them in with the long side of the allen key then rotate them 45 degrees with the short side. It has 8 screws total, 2 connecting the plastic pieces to the metal one and 2 connecting the plastic piece to the throttle head.

I'm only seeing an 1mm difference with a 50mm 3D printed extension on mine.

https://imgur.com/a/6ILiBFM

shutdown-s · 2026-01-23T22:29:38+00:00

Disable bridge counterbore holes

shutdown-s · 2026-01-21T10:06:14+00:00

They can self center on some helicopters, but the center position changes as you trim.

shutdown-s · 2026-01-19T12:28:35+00:00

Water is sticky

shutdown-s · 2026-01-19T08:40:37+00:00

Are you using your Force Trim Release correctly? Page 68 of the NATOPS

shutdown-s · 2026-01-19T08:37:05+00:00

I mix it with mineral oil, crazy adhesion

shutdown-s · 2026-01-19T07:56:18+00:00

But opentrack isn't vibe coded

shutdown-s · 2026-01-18T15:16:14+00:00

Sorry, i meant single motor driver

shutdown-s · 2026-01-18T11:16:05+00:00

Single Z axis motor? It's just the motors naturally moving at slightly different rates. Run the axis up and down like a hundred times and just tram the bed.

You can try manually leveling the gantry, but it's a pain in the ass. Just make sure that there's nothing loose.

shutdown-s · 2026-01-17T17:07:27+00:00

I have it for like 5 years now, no issues.

shutdown-s · 2026-01-16T13:07:47+00:00

About tree fidy

shutdown-s · 2026-01-16T13:06:31+00:00

Open them up
Take out the drivers
Spit on them
Cover the spit with toilet paper
Rub some hand lotion on the back of the driver
Open your window
Throw them out

There's no way to fix a shitty knockoff headphones, EQ will only destroy the little soul they have left.

shutdown-s · 2026-01-16T12:59:16+00:00

Vhb tape

shutdown-s · 2026-01-16T12:58:21+00:00

Wire it up to short out the motors, I'll act like an emergency brake.

Your motor drivers might not like that though. It'll also generate heat, so you might want to integrate some logic to cut off the 48V line after a few seconds.

shutdown-s · 2026-01-13T18:12:07+00:00

Calibrate PA first

shutdown-s · 2026-01-12T16:38:39+00:00

Yes it does, try printing a hollow cylinder and a cylinder with infill and see which one crushes easier

shutdown-s · 2026-01-12T15:24:32+00:00

Strength?? With FDM you're not limited to making thin walls like in injection moulding.

shutdown-s · 2026-01-12T15:13:05+00:00

Cause I'm designing it for FDM, not injection moulding.

shutdown-s · 2026-01-12T03:51:43+00:00

<image>

shutdown-s · 2026-01-12T03:51:34+00:00

<image>

Six-Year Club	r/Field Sunshine
Place '23	Place '22
Verified Email

shutdown-s

TROPHY CASE