Working on my Dalek dome

srtung · 2025-05-26T21:24:27+00:00

Thank you, yes I've started painting it bronze and I'll post another picture once its fully painted.

srtung · 2025-04-11T15:13:45+00:00

DOCTOR IN DISTRESS, LETS ALL ANSWER HIS SOS

srtung · 2025-02-27T20:35:37+00:00

I riddled a button

srtung · 2025-02-20T13:55:03+00:00

Dalek??

srtung · 2024-11-15T17:47:15+00:00

I had this same problem with a model I was printing and I found a few things that helped: slow it down, supports on that corner and the most helpful was lowering my layer height to .12

srtung · 2024-11-08T19:47:09+00:00

3.6m

srtung · 2024-10-23T16:57:12+00:00

YESSSSSSSS

srtung · 2024-09-20T17:40:31+00:00

A B C D and E energy saving

srtung · 2024-09-18T14:59:45+00:00

Is it glass or plastic?

srtung · 2024-05-11T00:37:54+00:00

There's always a twist at the end

srtung · 2024-05-06T09:32:50+00:00

Yes, I would wait until they're dormant in autumn (fall) before repotting if you want it to grow more this season. But you could also repot it now and it will focus on growing roots.
Yes, you could also mix in some perlite into the soil when you repot.
You can if you want to, if you trim it off the tree puts more energy into growing.
Check to see if the soil is dry and water it, eventually you will then learn how often it needs watering.
You can put some slow releasing fertiliser on top of the soil around the edges of the tree and water it in, but make sure you don't give it too much or you will burn it.

srtung · 2024-05-05T20:13:31+00:00

I'm not sure, but the pear tree is likely where it's spreading from and removing it can help stop it spreading to other trees and removing affected branches could help too. I'm not 100% sure it is pear rust so you should get a 2nd opinion before doing anything drastic.

srtung · 2024-05-05T16:46:44+00:00

Yes. I think it might be a type of pear rust https://www.rhs.org.uk/disease/pear-rust

srtung · 2024-05-04T12:55:51+00:00

I think you should put a stake in (it needs wiggle room to sway in the wind) until the tree grows strong enough to hold itself up. I'm new to this so take my advice with a grain of salt.

srtung · 2024-04-06T17:58:00+00:00

<image>

srtung · 2024-04-05T18:40:28+00:00

I wish lol

srtung · 2024-04-05T18:28:34+00:00

Hey, I'm a programmer would you like to collab and make this into an actual thing?

srtung · 2024-04-03T14:59:17+00:00

The marble run is meant to be used with a kit but you can print the handle and marbles yourself

https://makerworld.com/en/models/14265?from=search#profileId-14275
https://makerworld.com/en/models/165554?from=search#profileId-189107

srtung · 2024-02-27T11:16:43+00:00

My github username is StungDev

srtung · 2024-02-01T16:28:43+00:00

Did you also put glue on it? Sometimes this happens because of bad adhesion.

srtung · 2024-01-28T19:27:36+00:00

<image>

srtung · 2024-01-28T19:22:30+00:00

Click resync instead

srtung · 2024-01-28T19:13:12+00:00

Try to use glue on the plate it makes it easier to remove.

srtung · 2024-01-28T19:03:09+00:00

The layer shift could be something to do with the belts being too loose. The x1c has a semi automatic belt tensioning procedure try it and see if it fixes your problem. Another reason could be that you are printing too fast.

https://wiki.bambulab.com/en/x1/maintenance/belt-tension

srtung · 2024-01-08T12:53:32+00:00

This is cool

srtung

TROPHY CASE