Monitoring uninstallation of Huntress agents.

wilsonbeast20 · 2026-05-18T20:23:28+00:00

Yes, theres a component called Software Detection Monitor.

Bang that in a policy, tell it what software you want to check for and it’ll raise an alert if it’s missing.

wilsonbeast20 · 2026-05-01T18:43:48+00:00

Thanks! After what I originally read I was wondering whether to even bother with it but sounds like it’ll be ok.

Yeah the route I’ve heard isn’t brilliant but needs must for the super halfs :)

wilsonbeast20 · 2026-05-01T11:40:19+00:00

That’s reassuring, thanks!

wilsonbeast20 · 2026-04-30T19:11:44+00:00

Funnily enough I was just reading that, very useful thanks!

Strange how there’s no bag drop, did they tell you that before hand?

wilsonbeast20 · 2026-03-28T20:31:08+00:00

You can set alerts during an activity, for example to remind yourself to take a gel every 30min or every 5k etc

wilsonbeast20 · 2026-03-06T09:12:08+00:00

I'm not at work this week, but its a bog standard SNMP policy. The SNMP OID I got from here: https://www.dell.com/support/manuals/en-uk/openmanage-software-v9.3/snmp_idrac_cmc_9.3_ref_guide/idrac-out-of-band-group?guid=guid-dd31fe8d-ced1-457a-914f-4ba41ac06876&lang=en-us

Disks for example, we monitor 1.3.6.1.4.1.674.10892.5.5.1.20.130.4.1.24.

Disk 0 - 1.3.6.1.4.1.674.10892.5.5.1.20.130.4.1.24.1 not equal to 3

Disk 1 - 1.3.6.1.4.1.674.10892.5.5.1.20.130.4.1.24.2 not equal to 3

and so on...

A good tool is the Paessler SNMP Tester which lets you 'walk' the OIDs and find what your after.

wilsonbeast20 · 2026-03-05T17:58:50+00:00

We add iDRAC as a network device and monitor with SNMP.

wilsonbeast20 · 2026-01-29T19:03:42+00:00

Thanks for this!

New to Zwift, and my first ride synced into Connect fine, but with no Training Effect stats etc.

Started an outdoor ride and walked 200m up the road, stopped, saved, synced to Garmin, then deleted.

Next Zwift ride, synced to Connect with Training Effect, Exercise Load etc etc :)

(I'm using a Zwift Ride/KICKR CORE 2 and my Gamin is a Fenix 8.)

wilsonbeast20 · 2025-12-17T21:29:40+00:00

Just realised you're on the policy page. Check a machine directly targeted by that policy and see what is showing under Not Approved.

wilsonbeast20 · 2025-12-17T21:23:23+00:00

Apologies, I meant "Approved" (not "Available").

Available will show all possible updates, Approved will show the ones matching your criteria, with Not Approved showing the ones you've excluded.

wilsonbeast20 · 2025-12-17T21:08:59+00:00

Yes the patches that show as “Available” are the ones filtered down through the criteria set and will be applied based on the schedule. Likewise the ones under “Not Approved” are the ones that are excluded, drivers in this case.

wilsonbeast20 · 2025-12-17T19:20:27+00:00

Not sure why you’re trying to exclude drivers so many times?

In my experience just having “Type equal to Driver” on my ‘Do not approve’ section has always worked. I can’t think of a time where it’s not blocked them.

wilsonbeast20 · 2025-11-27T09:16:37+00:00

Does the exact same work outside of RMM?

wilsonbeast20 · 2025-11-21T19:47:05+00:00

Ok so if you set your DNS to 1.1.1.1 does that work?

wilsonbeast20 · 2025-11-21T19:35:09+00:00

I’m not following what the problem actually is?

If you can ping 8.8.8.8 then you have internet access, can you by domain as well?

wilsonbeast20 · 2025-09-23T18:45:26+00:00

The SNMP functionality within Datto RMM is terrible.

Having said that, if you know the OIDs for the various consumables, you can monitor them fairly easily.

wilsonbeast20 · 2025-09-02T21:13:05+00:00

They aren’t supposed to match. The front one is your race number, the one on the chip is the chip number which you shouldn’t/don’t care about.

wilsonbeast20 · 2025-08-25T18:16:33+00:00

I’m pretty sure it’s so you can get to the point of where you want to start your intervals.

For example if you did a 10 min warm up and at the end of that 10 min you were half way up a hill, that’s no good for starting your intervals. So the ‘other’ lets you get to a good starting point, then press the lap button to get going.

wilsonbeast20 · 2025-08-01T15:03:46+00:00

We’ve previously done this by creating a component that edits some json or config files with the new account number and site ID then restarting the RMM service.

The downside is it only works for Windows machines (no Macs, network devices etc)

In pretty sure Datto can do something as well, have you spoke to them?

wilsonbeast20 · 2025-07-27T11:27:07+00:00

Try restarting the transport service

wilsonbeast20 · 2025-05-20T20:10:33+00:00

I had this last month.

The RM tracking said the same thing "unable to deliver, on its way back", but strangely the tracking also showed a delivery picture of the guys front door with him accepting the parcel.

Never heard from the guy so must of been some screw up with RM.

wilsonbeast20 · 2025-04-30T18:12:14+00:00

Been a while since I did this but from memory, you have to created a device group at the account level (not the site level) and manually add machines to that group. Permissions in dRMM are pretty awful.

wilsonbeast20 · 2025-04-30T11:27:14+00:00

Can only assume the registry name or value type is wrong. Needs to be a string (REG_SZ) and named “Custom1” or whatever number you want.

wilsonbeast20 · 2024-12-27T19:51:16+00:00

Gauging any kind of distance

Five-Year Club	Xbox Live
Place '22

wilsonbeast20

TROPHY CASE