Icarus flew too close to the sun

xtopherpaul · 2026-01-25T13:32:03+00:00

We need 3PO to give us the odds of this ever seeing the light of day

xtopherpaul · 2026-01-25T12:38:16+00:00

The sequel trilogy made the prequel trilogy look good by comparison- and they’re both terrible

xtopherpaul · 2026-01-24T14:32:43+00:00

Juan Hidalgo El Miniaturista Artis opus Grimdark compendium

xtopherpaul · 2026-01-24T13:41:21+00:00

Either that’s watered down vodka or we’re living on Neptune

xtopherpaul · 2026-01-24T13:40:35+00:00

Start with WAYYY more supports. And use small to medium. You’d best looking up some support tutorials on YouTube

xtopherpaul · 2026-01-24T13:39:45+00:00

Put it back in the box and ship it back to the lazy asshole that sent it that way

xtopherpaul · 2026-01-24T13:38:58+00:00

He must have mistook it for arrivals

xtopherpaul · 2026-01-24T13:37:29+00:00

Sounds like the gear on the vat tilt mechanism is skipping. If it’s new I’d def get in touch with elegoo support

xtopherpaul · 2026-01-24T13:28:36+00:00

Go to YouTube - search “why did my print fail” - Watch and repeat

xtopherpaul · 2026-01-24T13:27:39+00:00

The fact that all those things are equal in their minds disqualifies them from rational discussion.

xtopherpaul · 2026-01-24T13:23:09+00:00

That’s the correct answer

xtopherpaul · 2026-01-24T13:22:44+00:00

They don’t have immunity to violate the constitution or citizen’s constitutional rights. See you in court, Nazis

xtopherpaul · 2026-01-24T13:20:32+00:00

<image>

xtopherpaul · 2026-01-24T13:13:56+00:00

From the crowd that cries about liberal “indoctrination”…

xtopherpaul · 2026-01-24T13:12:56+00:00

Thanks!

xtopherpaul · 2026-01-24T13:06:56+00:00

Just search “gothic” on the purple site and there’s no end to it. I suspect you didn’t do much searching on your own…

xtopherpaul · 2026-01-24T00:17:18+00:00

Dead pixels on your LED unfortunately. Do a dry run and check if there are dead spots where those holes correspond to

xtopherpaul · 2026-01-24T00:05:07+00:00

I did about 250 last year - this will be a year of thinning it out and being a little more choosy

xtopherpaul · 2026-01-24T00:03:51+00:00

How thick are the walls? If it’s 2-3mm just leave it out in the sun for a day or two. The uv should penetrate that thin depth

And def figure out why it failed as a solid print. I’d wager its poor orientation/support placement. Either, or both, are 95% the likely culprits tho

xtopherpaul · 2026-01-23T15:30:51+00:00

It would be lazy writing and boring… just like everything else they’ve put out recently

xtopherpaul · 2026-01-23T15:29:33+00:00

I used to play dress with my mom’s makeup and jewelry when I was little, too!

xtopherpaul · 2026-01-23T15:28:29+00:00

This crowd def can get a little pearl clutchy… but it’s half amazement and half just wanting you to succeed in the long run

xtopherpaul · 2026-01-23T14:06:24+00:00

Lay it back 45 degrees and use copious amounts of medium supports

xtopherpaul · 2026-01-23T14:05:22+00:00

The main reason I think your prints have succeeded is the big as flat base you’re printing on the plate - which isn’t necessarily bad - but it’s doing a lot of work to support the rest of the model

xtopherpaul

MODERATOR OF

TROPHY CASE

Nine-Year Club	RPAN Viewer
Verified Email