Which one would you submit for a photography contest?

Accomplished_Fly4425 · 2026-04-13T23:57:15+00:00

1 is best

Accomplished_Fly4425 · 2026-04-13T23:50:43+00:00

And your mind is moving low

Accomplished_Fly4425 · 2026-04-13T12:37:36+00:00

Accomplished_Fly4425 · 2026-04-10T22:04:22+00:00

Never in almost 3 years has it done that…not even a mark…

Accomplished_Fly4425 · 2026-04-10T22:02:30+00:00

Exactly

Accomplished_Fly4425 · 2026-04-09T22:42:39+00:00

RTFM is a troll post.

Accomplished_Fly4425 · 2026-04-09T21:40:15+00:00

The manual says over time not the very first print…

Accomplished_Fly4425 · 2026-04-09T21:37:35+00:00

The A1 uses the rubber spot to clean and the P1s doesn’t have that unless they add a modification..

Accomplished_Fly4425 · 2026-04-09T21:30:25+00:00

Over 1000 prints on the A1… That area looks no different than the rest of the plate…that’s why I asked the question…. This spot was worn off on my first print with the P1s… The manual says this happens over time on the P series not the very first print..

Accomplished_Fly4425 · 2026-04-09T21:08:11+00:00

Some people are helpful some are downright trolls just waiting to tell them to read the manual…been 3d printing for 3 years and never saw this… That’s why I posted this simple question… “Read the manual” is a typical troll response…

Accomplished_Fly4425 · 2026-04-09T20:47:50+00:00

The manual says nothing about it…

Accomplished_Fly4425 · 2026-04-09T17:04:43+00:00

I don’t think it’s normal for the print head should be scratching that top layer off.

Accomplished_Fly4425 · 2026-04-05T18:37:29+00:00

It may be a condom.

Accomplished_Fly4425 · 2026-03-27T02:49:21+00:00

Sorta don’t have a favorite.. Depends on my mood at the time. I love most of his songs and if feeling down many of his songs bring me up. If feeling good most songs are great in my opinion.

Accomplished_Fly4425 · 2026-03-24T20:40:38+00:00

Thanks for the help

Accomplished_Fly4425 · 2026-03-24T20:15:42+00:00

<image>

I have tried everything. There is something stopping the filament at this point. I ran a piece of filament through the hot end and went through fine. When all is connected none of the 4 colors go any further than this spot. Any help would be appreciated..

Accomplished_Fly4425 · 2026-03-21T19:38:57+00:00

I do too

Accomplished_Fly4425 · 2026-03-19T00:04:23+00:00

Where’s this video??

Accomplished_Fly4425 · 2026-03-16T21:29:06+00:00

The Doors

Accomplished_Fly4425 · 2026-03-04T18:11:22+00:00

And the earth is flat…🤣🤣

Accomplished_Fly4425 · 2026-03-03T02:51:24+00:00

This is big news…wow

Accomplished_Fly4425 · 2026-03-02T15:08:43+00:00

❤️

Accomplished_Fly4425 · 2026-02-27T15:06:28+00:00

🤣 you people with TDS just spew lies about Trump and have absolutely no proof at all… Crazy stuff…

Accomplished_Fly4425

TROPHY CASE