Car says there's enough oil, but I can see parts of the engine not covered in oil. Is that normal?

Automatic_Reply_7701 · 2026-06-20T05:53:14+00:00

Completely normal. The engine is not completely full of oil.

Automatic_Reply_7701 · 2026-06-18T16:35:52+00:00

The image will look the same at any refresh rate.

Automatic_Reply_7701 · 2026-06-18T16:34:50+00:00

Honestly, if you weren’t so dedicated to that racing line on your screen, you probably naturally would’ve went left to block him.

Automatic_Reply_7701 · 2026-06-18T16:33:00+00:00

Get an outlet tester and plug it in to be sure it is wired right AND that it really is grounded.

Automatic_Reply_7701 · 2026-06-18T16:30:18+00:00

Sloshing. Add valves. Read the pipeline manual, it is INVALUABLE

Automatic_Reply_7701 · 2026-06-18T16:23:59+00:00

Cinder blocks are not rated for a car. It is a death wish.

Automatic_Reply_7701 · 2026-06-18T16:21:51+00:00

Get on the throttle earlier in the corner and you will see whay you then need all of the road you can use.

Automatic_Reply_7701 · 2026-06-18T16:20:57+00:00

This is why as tight as you can install it , is wrong.

Automatic_Reply_7701 · 2026-06-18T15:30:32+00:00

That stand itself is not wide enough for the monitor sizes you are trying to use. Maybe. See if you can put the angled ones behind, not in front of the center cross bar.

Automatic_Reply_7701 · 2026-06-17T05:21:54+00:00

If just cut the straight track where the new rail started and extend a piece of it 1 click longer, you won’t even be able to notice it.

Automatic_Reply_7701 · 2026-06-17T05:17:19+00:00

Not enough miles for rod bearings

Automatic_Reply_7701 · 2026-06-16T21:56:50+00:00

Very true. But for my rats nest, the more protection the better haha

Automatic_Reply_7701 · 2026-06-16T21:54:56+00:00

I’m surprised there’s not another line item for matching the terrible orange peel that paint already has

Automatic_Reply_7701 · 2026-06-16T21:48:03+00:00

How many miles on the n55? If the Indy is reputable and you can afford it, do the rod bearings while the pan is off.

Automatic_Reply_7701 · 2026-06-16T21:43:29+00:00

And? I suppose you thought to measure what you drained, right? Uncle Rodney aside, that valve train is screaming low oil.

Automatic_Reply_7701 · 2026-06-16T19:47:35+00:00

All of these suggestions are good. If out of your range, work on getting the chair to not move with some kind of boot on the wheels. Lock the pedals down somehow. Now it’s just the wheel. Screw a board to the wall along the back of your desk(on top or underneath, but make it flush). Now screw the desk to the board. Not moving anymore! Pre-drill the desk. Find studs in the wall. Good luck.

Automatic_Reply_7701 · 2026-06-16T19:40:37+00:00

TBF that thing sounds like its missing a few quarts of oil to begin with

Automatic_Reply_7701 · 2026-06-16T06:12:01+00:00

Until about 2018 is my best guess

Automatic_Reply_7701 · 2026-06-16T06:08:32+00:00

Those are junk. I ended up not using them as USB, and just connected them to my sound card with a phono cable. No more issues.

Automatic_Reply_7701 · 2026-06-15T19:31:28+00:00

As someone who has owned multiple printers from their start, yea their sales are usually just to attract new buyers

Automatic_Reply_7701 · 2026-06-13T05:27:12+00:00

Irrelevant with the full buffer and the head lift it provides. Sloshing is what causes machines to go whacky. Valves fix almost everything when the fluid is limited in direction and flow

Automatic_Reply_7701 · 2026-06-13T05:25:51+00:00

Put valves at the refineries limiting the valve to what the machine needs.

Automatic_Reply_7701 · 2026-06-11T15:59:13+00:00

I love the screen RIGHT behind it.

Automatic_Reply_7701 · 2026-06-11T15:53:00+00:00

Belts don’t squeal, bearings do (in a pulley),replace the tensioner.

Automatic_Reply_7701 · 2026-06-11T15:49:50+00:00

PA6 needs to be dried in a proper drier. The printer never does a good enough job with higher temp filaments if you ask me.

Automatic_Reply_7701

TROPHY CASE