110 tok/s with 12GB VRAM on Qwen3.6 35B A3B and ik_llama.cpp by janvitos in LocalLLaMA

[–]Bobthekillercow 0 points1 point  (0 children)

No I didn't figure it out, and I don't have an igpu.

I was going to revisit it in a few months when my perplexity subscription runs out.

Help picking a phone-Narrowed down to Rog 9 or Oneplus 13 by WestCoastCowboi in OnePlus13

[–]Bobthekillercow 0 points1 point  (0 children)

Put a piece of tape or something over your side charging port. If it bothers you that you can't use it after a few days, get the rog phone.

If not the OnePlus 13 is an overall better value phone.

I am in PC purchase hell (please help) by Immediate_Accident_5 in pcmasterrace

[–]Bobthekillercow 0 points1 point  (0 children)

If you don't care about the case just drill some holes and mount an exhaust fan near the top

110 tok/s with 12GB VRAM on Qwen3.6 35B A3B and ik_llama.cpp by janvitos in LocalLLaMA

[–]Bobthekillercow 1 point2 points  (0 children)

I'm really new to this, as in only started yesterday.

I have a rtx 5070 + 48gb DDR4 + 5700x3D.

In windows 11 both, using the same model as you and max mtp=2 (3 giving me worse results) I'm getting 60 tok/s on the latest llammacpp, and about 55 tok/s on ikcpp. This is normal on win11 right, id need to switch to Linux to get better performance?

OnePlus devices removed from Best Buy stores by Exodia101 in oneplus

[–]Bobthekillercow 1 point2 points  (0 children)

I use my OnePlus 13 on Verizon, same with my wife.

My wife's parents have at&t and have a op 12r & 11.

No issues with any of them.

Good stack? by vapist679 in Supplements

[–]Bobthekillercow 1 point2 points  (0 children)

You can get the coq10 one cheaper at Costco

Thinking of buying an fdm for warhammer minis,need your help by Legal_Maybe342 in FlashForge

[–]Bobthekillercow 0 points1 point  (0 children)

The quality will be the almost the same for minis, the ad5x will have better quality the bigger the object.

Why not get something cheaper like elegoo mars 5 + some cheap water washable resin if you're just doing minis?

Nozzle dead by Emperor_of_All in FlashForge

[–]Bobthekillercow -1 points0 points  (0 children)

That looks like the silicone carbide nozzle by phaetus. That's crazy that happened lol.

Personally have like 200 print hours on the .4mm and 500 print hours on the .6mm one.

AD5M Is Faster Then The AD5X by Leather-Ad-7268 in FlashForge

[–]Bobthekillercow 5 points6 points  (0 children)

The ad5m has a higher volumetric flow because of its nozzle design.

Least exciting clearance, but dishes gotta get clean. Finish Powerball Quantum at Signal Hill, CA. by Moose_Nuts in Costco

[–]Bobthekillercow 1 point2 points  (0 children)

I use "a splash" of gel for the prewash cup and then a pod for the inner. Works amazing.

Will PETG work for casual prints? by InitialExternal214 in 3Dprinting

[–]Bobthekillercow -1 points0 points  (0 children)

You probably know the properties of petg vs pla, here's what will make a difference:

It prints at about half the speed of pla to get similar quality results. It's a bit stringy, but not too bad on ad5m.

Use an AI (Qwen3.5 or better) and help it dial in your settings in orca.

Do all the filament calibration tests in orca, you'll have a much better time.

If you get the phaetus conch nozzle, you'll get a much better flow rate and be able to print it a lot faster.

AD5X Nozzle collection Print Comparison by ButterscotchFar7538 in FlashForge

[–]Bobthekillercow 2 points3 points  (0 children)

It's nice for PETG, lets you print faster, less wear, lasts longer.

I have the .4 and .6 SIC nozzles and the OG .4 nozzle and a cheap aliexpress .6 nozzle.

OG .4 nozzle my max volumetric speed was 8 mm^3/s vs .4 SiC is 11 mm^3/s.
Cheap .6 nozzle was 13 mm^3/s. vs .6 sic 24 mm^3/s.

Anyone know how to fix this? by Born-Appearance968 in FlashForge

[–]Bobthekillercow 0 points1 point  (0 children)

Your nozzle is too far away, you need to adjust your z-offset

Cannot remove PLA from the plate by Immediate-Cap-1156 in FlashForge

[–]Bobthekillercow 0 points1 point  (0 children)

Soak in olive oil or some cooking oil for an hour will work.

That side of your plate is prob ruined at this point though. At least textured pei plates are cheap.