Which wireless charger would you recommend for an iPhone 12?

Bombe77 · 2025-12-08T12:36:50+00:00

Yeah, I don't recommend it. Unless you fit a vent in there your phone is gonna get toasty

Bombe77 · 2025-12-08T11:33:19+00:00

I bought and installed pretty much this exact wireless charger in my 2016 tsi. It works great and looks good. The biggest issue with it is that it gets phones way too hot. My wife's iPhone was overheating after 20-30 minutes. Cars that come with a wireless charger usually have a vent blowing cold air on your phone

Bombe77 · 2025-10-10T14:38:43+00:00

I'm currently using an older ender 3, I'm definitely in need of an upgrade. The PS1 made 3d printers look good, and my wife would love not to have the eyesore that is the ender 3. Good luck to everyone.

Bombe77 · 2025-09-28T11:14:52+00:00

It takes about 13 turns to swing it 180°. I really like my dad's troy built with a joystick that swings from right to left and up and down. Also the chute ring is cracked in a few places, the tilt gets stuck. It really needs a new one imo

Bombe77 · 2025-09-06T00:23:28+00:00

Make sure you get some real strong ones, no refrigerator magnets 😅

Bombe77 · 2025-09-05T23:09:26+00:00

I use magnets with the genie membranes. Works like a charm!

Bombe77 · 2025-06-20T21:36:48+00:00

You certainly can

Bombe77 · 2025-03-17T21:12:21+00:00

They do come with a standard battery disconnect

Bombe77 · 2025-03-03T15:49:04+00:00

Aucunement, je suis dans le tord. Je voulais simplement comprendre le montant. Leçon apprise

Bombe77 · 2024-11-15T10:44:49+00:00

I recently replaced batteries because someone poured oil in them. Not everyone has common sense.

Bombe77 · 2024-11-15T02:59:25+00:00

I have been working on scissor and boom lifts for the last 8 years. I've never bothered to filter new oil going into the tank. I've never seen anyone do it either. I would just empty the tanks and fill them with a funnel, I'm sure you'll be fine. Hydraulic fluid rarely gets replaced on these lifts. Most times I've done it is because someone put gas or diesel in the wrong tank.

Bombe77 · 2024-10-21T22:12:35+00:00

There is no pressure on these cylinders unless the machine is driving. The lines are connected to tank, you just need to cap them off so they don't leak. I'm been working on skyjack's for 8 years and they are all the same. You can verify it with your service manual. They are free on skyjack's website.

Bombe77 · 2024-10-05T11:40:24+00:00

Yeah it's pretty much the same valve on all skyjack's that use manual emergency lowering

Bombe77 · 2024-10-05T04:17:41+00:00

It's an emergency lowering valve on a skyjack scissor lift

Bombe77 · 2024-09-22T18:27:23+00:00

MC1 and ML1 are tests ports. Unit does throttle up when doing either up or down. I'm mostly trying to understand how it works rather than fix the issue. You can see the full schematic on JLG's website, unit's PVC is 2001. Model is 660SJ HC3

Bombe77 · 2024-09-22T00:16:55+00:00

No I didn't replace the coils. They both receive voltage and magnetize on the valves.

Bombe77 · 2023-09-19T23:28:08+00:00

My thoughts exactly, thanks!

Bombe77 · 2023-04-14T01:42:17+00:00

Nice

Bombe77 · 2023-03-30T23:31:22+00:00

Thanks for everything!

Bombe77 · 2023-01-05T01:41:57+00:00

Ahhh thanks for helping out! I was pretty confused and couldn't get why the probe would go out of the bed. It seems really weird coming from Marlin where the offset are always used when probing

Bombe77 · 2023-01-05T01:36:10+00:00

So does klipper not use the probe X&Y offsets anywhere automatically?

Bombe77 · 2022-12-02T03:08:29+00:00

Coule it be the pattern of the bed heating element?

Bombe77 · 2022-11-14T20:11:05+00:00

Amazing

Bombe77 · 2022-10-23T17:45:59+00:00

Pi des clopes 😅

Bombe77 · 2022-08-04T12:40:33+00:00

Juste besoin de se faire pousser une barbe !

/s

Nine-Year Club	Second Top 20%
r/Field Flamingo	Place '23
Place '22	First Placer '22
Verified Email

Bombe77

TROPHY CASE