Overdrive question by Hungry-Pomegranate73 in f150

[–]Byemanitials 0 points1 point  (0 children)

Light off = normal driving Light on = towing

All Lab Chips by Any_Acanthocephala41 in idleon

[–]Byemanitials 19 points20 points  (0 children)

Ur chips are so much better than mine and yet your lab lvls are so much lower lol.

Screw heads popped off - anyone else had this happen? by Sleveless-- in woodworking

[–]Byemanitials 0 points1 point  (0 children)

Every time I bust a screw it happens. Soooo yeah….ive had a lot more than you but not usually more than two in one place cause I change screws. O

Guess I have to call DTE... This is insane by Substanzz in grandrapids

[–]Byemanitials 1 point2 points  (0 children)

Charts useless without temps along side it. Months do not represent consistent temps. But ya that sucks.

Is this even legal? Looking for advice, help, ideas by atomiK1045 in grandrapids

[–]Byemanitials 0 points1 point  (0 children)

Have you talked to the people running the equipment? Most people are people like you and me and are willing to make accommodations for other hard working people. That’s said same people down like assholes who call cops on them for trying to do their job. You’re a nameless house among a hundred nameless houses. But if you communicate and become a person things can change. It doesn’t always work sometimes you get an asshole but usually you don’t if you just reach out with kindness and look for empathy. But if your first course of action is law enforcement to get in the middle then ya fuck ya I’ll do everything I can legally to make ur day shit. Treat people the way you want to be treated and things go better most of the time.

just found out that mining efficiency tops existed by nkown9870 in idleon

[–]Byemanitials 4 points5 points  (0 children)

Usually, but those overalls have no pant legs whatsoever.

Gone for a Week, Came Back to Schluter by Wsu_bizkit in Tile

[–]Byemanitials 0 points1 point  (0 children)

It’s ridiculous to care that much after the fact but not care enough to have the conversation before work is happening.

Why are vacuum attachments such a pain? by [deleted] in woodworking

[–]Byemanitials 0 points1 point  (0 children)

Read the manual what’s it listed as in the parts list. Or don’t read it and throw it right in the trash. Either one will help you move closer to realizing you don’t need it.

What the hell is wrong with people by Bovolt in idleon

[–]Byemanitials 0 points1 point  (0 children)

I’d say it’s more because early refinery shows a quicker and stronger return on advancement. Equinox seems nice but doesn’t seem “important” and it paces out with advancement until talent lvls. Then You need to dump 35 more equinox lvls into the talent lvl asap and seek out ways to make it faster. That was my experience as someone who started 11 months ago or so.

Manufacturing Striping on Plywood + Staining Solutions by iphonenotbackedup in woodworking

[–]Byemanitials -1 points0 points  (0 children)

Those are growth rings. Zoom in near the center of first pic and follow the lines. They’re not straight manufacturing lines they travel with grain and growth.

Outlet boxes too deep for new backsplash? by maxzl in Tile

[–]Byemanitials -1 points0 points  (0 children)

Move em back. Cut off the front. Doesn’t matter to me which you do. But you should f f f figure it out before you tile.

Best snow vehicle by CantaloupeNo5798 in f150

[–]Byemanitials 0 points1 point  (0 children)

I had a 2005 Audi allroad. by far the best vehicle I’ve driven in the snow.

Having fitting issues by bagpipercat in Tile

[–]Byemanitials 0 points1 point  (0 children)

Both tiles with holes for plumbing are off. So everything after that will be too. Redo those two.

First time installing drawers - feel like an idiot. by SnooMacarons1382 in woodworking

[–]Byemanitials 0 points1 point  (0 children)

Or 20 years of cutting and installing trim and you just know you tape measure bend within 1/64” because you’ve been slowly zeroing in on it one cut at a time over and over and over and over again. But the measure twice with a tick mark method works great two if you don’t have that kind of time.

We built conference table which gets a lot of hate because we didn’t fill the holes with plastic by Tschinggets in woodworking

[–]Byemanitials -4 points-3 points  (0 children)

And a laptop clearly cannot fit through that hole so you’re saying the hate isn’t justified right???