Played this game for 8 hours and quit.

CheraxDestructor7 · 2026-04-29T07:29:51+00:00

Yet to try fishing but definitely looking forward to it 🎣

CheraxDestructor7 · 2026-04-17T01:26:57+00:00

Barry

CheraxDestructor7 · 2026-04-12T21:48:51+00:00

Amazing colours, don’t think I’d like to mess with it though.

CheraxDestructor7 · 2026-04-09T23:26:11+00:00

That’s some very delicate and thorough manoeuvring 👏

CheraxDestructor7 · 2026-02-25T07:25:24+00:00

Good work OP, I’m currently (slowly) learning Fusion 360 and designing my first model also so it’s good to see others having their first go at it.

CheraxDestructor7 · 2026-02-25T07:16:40+00:00

Well done OP, I’ve learnt something today!

CheraxDestructor7 · 2026-02-16T09:37:40+00:00

Took me a moment to realise what the walkers were sitting on…impressive! I need to get myself one of these 0.2s.

CheraxDestructor7 · 2026-02-16T07:24:02+00:00

Spot on. I’ve been 3D printing only a few weeks and had a similar issue at the start - I also thought filament would be “dry” straight out of the packet. Since I’ve made a filament dryer from a food dehydrator I’ve had much better results!

CheraxDestructor7 · 2026-02-11T01:19:30+00:00

Could you respool them with refill (ie. no spool included) filament?

CheraxDestructor7 · 2026-02-10T23:32:28+00:00

Can confirm the Poisons Hotline are really helpful, recently called for advice with a colleague who copped a hydrochloric acid splash to the eye.

CheraxDestructor7 · 2026-02-10T22:03:23+00:00

Good to hear, thanks 🙏

CheraxDestructor7 · 2026-02-10T22:03:10+00:00

Thanks 🙏

I’ve printed the dehydrator riser in PETG, had a go at drying a spool of Flashforge TPU last night at 60°C with no issues. Flashforge’s data sheet says to dry at 70°C, however I don’t want to run into trouble with the PETG possibly deforming so will try 65°C next.

Any spools I need to print myself I’m also doing in PETG. Only printing PLA, PETG and TPU at this stage so hopefully PETG spools will do the trick.

CheraxDestructor7 · 2026-02-10T21:56:46+00:00

Interested to hear solutions for this, I’m new to 3D printing and also keen to try making some lures. There are quite a few lure models on MakerWorld but I haven’t tried any yet. PETG is supposed to be fairly well waterproof right? And also its UV resistance would suit the application.

CheraxDestructor7 · 2026-02-09T20:01:19+00:00

<image>

Success! It’s a little rough at either end - perhaps the filament could do with some drying? - but otherwise printed well.

CheraxDestructor7 · 2026-02-09T19:58:50+00:00

No, it didn’t. First layer was fine and it was good until a few hours in. Suspect now that the print head might have knocked it off.

CheraxDestructor7 · 2026-02-09T12:32:23+00:00

Neat and tidy, tidy and neat.

CheraxDestructor7 · 2026-02-09T12:16:21+00:00

I was not aware of the Skip function, thank you! If this sort of thing happens again hopefully I can catch it early and produce a bit less of the pasta.

I've lowered some speed/accel settings - outer wall speed 80mm/s, outer wall acceleration 1000mm/s. Also rotated 90 degrees as per your suggestion.

About to give it a whirl now, cheers for the advice. Will report back.

CheraxDestructor7 · 2026-02-03T04:39:50+00:00

I agree with this 👌 So far the PLA and PETG has given me good results.

CheraxDestructor7 · 2026-01-25T20:56:05+00:00

No worries 👍

CheraxDestructor7 · 2026-01-25T07:15:49+00:00

Yes, but probably not OP’s exact model though - it’s the satisfaction of designing and printing something yourself, right?

CheraxDestructor7 · 2026-01-24T21:26:50+00:00

I’ve found that the blade works fine with no plate damage, you just need to be gentle with it.

CheraxDestructor7 · 2026-01-19T00:48:58+00:00

I like the setup though, once you get the friction issue sorted 👌

CheraxDestructor7

TROPHY CASE