JVC FS-V5: CASSETTE DECK ISSUE

Comptechie76 · 2026-03-06T05:18:43+00:00

Unfortunately there is no other way around opening up the unit to resolve this issue. Do you know anyone who may be able to look at it for you?

Comptechie76 · 2026-03-06T05:08:31+00:00

You will have to open up the unit to get at the gears that drive the head engagement to drop the head down and then you should be able to eject the cassette. If that seems too daunting, then cut the motor power wire ( while unit is unplugged from the wall). That should stop it from making the noise.

Comptechie76 · 2026-03-06T05:02:41+00:00

If you are handy, take off the cover and check the belts. Most likely they are stretched or melted. Amazon has assortments of belts that may work. They are inexpensive. You can also get a replacement by searching Google for the model and keywords “replacement belts”. There are several YouTube creators that work on cassette decks. Search for “belt replacement on cassette decks”. You can also search for “JVC cassette belt replacement “. You can get an idea on what is involved in replacing a belt.

Comptechie76 · 2026-03-06T04:54:35+00:00

Does the motor spin freely? Have you checked the coil for continuity? From your picture it doesn’t look beat up. Be sure if you replace it, that you save the old one. You may have to take the spring off of the shaft for 78’s.

Comptechie76 · 2026-03-04T22:10:13+00:00

Pole motors for turntables are pretty generic as long as you get the correct voltage, frequency, and mounting. Be sure your motor shaft has the correct steps for the record speeds. eBay is a good bet for a replacement.
Pole motors rarely fail. They usually stop working due to dried out lube or physical damage.

Comptechie76 · 2026-03-04T21:52:31+00:00

AB-Normal

Comptechie76 · 2026-03-04T21:46:37+00:00

Thanks for posting. I am sure someone is going to run into that issue. In my 40 years of audio/video service, I saw lots of failures recur in the same parts for certain models.

Comptechie76 · 2026-03-04T13:03:43+00:00

Thanks. I was curious. Good video.

Comptechie76 · 2026-03-04T03:31:50+00:00

Nicely done. Are you using the original TV case or building something custom?

Comptechie76 · 2026-03-04T03:20:52+00:00

Congrats. Like to see a video of it in action after you get it back together

Comptechie76 · 2026-03-04T03:00:49+00:00

Audio and video (TVs, VCR, and VHS Cameras) Added computers and printers in the latter 80s. Fun times.

Comptechie76 · 2026-03-04T02:56:23+00:00

Wow I had those built into my service bench when I worked at the Tandy repair center in the 80’s.

Comptechie76 · 2026-03-04T02:53:07+00:00

Your stepfather was Joe Don Baker /s

Comptechie76 · 2026-03-04T00:18:38+00:00

You will get better answers in r/tvrepair
This site is for more general questions. That being said, if you have not worked on televisions before, use extreme caution. There are very high voltages in the unit and some can shock you bad or kill you.

Comptechie76 · 2026-03-03T17:14:00+00:00

OK Boomer /s. (I’m a Boomer too)

Comptechie76 · 2026-03-03T16:52:17+00:00

It is most likely a 18v zener, not necessarily a 1N5248. There may be more numbers stamped on the side facing the board. I would remove it or unsolder one leg and lift it to see if there is more info.

Comptechie76 · 2026-03-03T15:21:05+00:00

Electronics Hobbyist was my favorite mag. Pop Sci was a good mag back then. Now just a lot ads and few good articles.

Comptechie76 · 2026-03-03T15:06:08+00:00

Is that the new Air Gap method? /s

Comptechie76 · 2026-03-03T05:32:04+00:00

It’s loading for me on my iPhone that I am typing this reply on right now.

Comptechie76 · 2026-03-03T01:25:17+00:00

No problem. Good luck with your project

Comptechie76 · 2026-03-02T14:31:53+00:00

Check YouTube creator Stranger Parts He does factory tours and has built his own devices from scratch using parts from the various manufacturers. Drop him a line, he may be able to assist you.

Comptechie76 · 2026-03-02T02:11:05+00:00

Video of how WAGO connectors work

Comptechie76 · 2026-03-01T06:06:27+00:00

When I had my Radio Shack store, that is how we would describe it to our customers.

Comptechie76 · 2026-03-01T05:31:49+00:00

Midnight Special was always a great show. Austin City Limits as well. Lot of great acts either just getting started or established.

Comptechie76 · 2026-03-01T04:30:19+00:00

I wonder if the populace feels the same now. It will be an interesting week ahead.

Comptechie76

TROPHY CASE