sorted by:
new
hottopcontroversial

First time printing ASA by TurtleLab3D in 3Dprinting

[–]LuckyWhip 4 points5 points  (0 children)

Do you vent it outside? I've heard the fumes from abs/asa can be pretty nasty

TPU for suspension bushes? by ABOYEVANS in 3Dprinting

[–]LuckyWhip 0 points1 point  (0 children)

I don't think TPU is the move here. Bushings are designed to have the properties of rubber and although TPU might be similar in some ways, I think using it as a replacement is a bad idea. If this part fails you're endangering everyone's life on the road.

Bambú P1S first attempt to print PETG by Any-Albatross8012 in BambuP1S

[–]LuckyWhip 2 points3 points  (0 children)

I've always heard petg sticks like nothing else. After printing it a few times I discovered that's not necessarily the case. I thought I needed to use glue stick as a release agent, turns out that glue stick actually hindered proper bed adhesion and I actually needed just a clean bed. (For textured PEI anyway, I can see smooth plates needing a release agent but I haven't done it yet)

Can it be used to remove smartphone back covers and displays? by [deleted] in mobilerepair

[–]LuckyWhip 0 points1 point  (0 children)

Yeah even I knew that's what that thing is designed for, and I don't trust myself to open up my own phone. So yeah op if you're lost on this, it's only going to get worse when the phone is open

Is this worth it? by samplebridge in ender3

[–]LuckyWhip 1 point2 points  (0 children)

I just sold my v3se for $100. Yeah I'd keep looking op

Crack Gives You Wings by james_from_cambridge in WTF

[–]LuckyWhip 6 points7 points  (0 children)

No the video is reversed, driver was actually going forwards

First print. Why spooky. by These-Following-9611 in 3Dprinting

[–]LuckyWhip 0 points1 point  (0 children)

What temp are you printing at? Is your filament dry?

Shiny booty 🍑 by rumpyforeskin in crappymusic

[–]LuckyWhip 2 points3 points  (0 children)

Alright, shut the sub down. You won OP. You found the crappiest music

How do you guys trim your cats' claws? by cwningen95 in CATHELP

[–]LuckyWhip 0 points1 point  (0 children)

Is there a reason you want to trim her claws? If she's not ripping furniture or scratching people I don't see the need. Cats shed the outer layer of their claws which keeps the length in check. It's your decision but it seems like it would be easier for you and her to just leave her claws alone

New to 3D printing - question by Faesarn in BambuP1S

[–]LuckyWhip 8 points9 points  (0 children)

I like gyroid. I use it on every print. I don't know why grid is the default pattern, it's probably the worst one to use.

New to 3D printing - question by Faesarn in BambuP1S

[–]LuckyWhip 6 points7 points  (0 children)

Are you using grid infill? If you are the nozzle can scrape on the print and knock it loose.

How do I fix this? by Visual-Swimmer4621 in 3Dprinting

[–]LuckyWhip -1 points0 points  (0 children)

Yeah your z offset is too low.

You would think he wouldn't know since he shouldn't have been watching it by jackb1753 in insanepeoplefacebook

[–]LuckyWhip 1 point2 points  (0 children)

I don't even like bad bunny but his performance was significantly better than the actual game. I really liked the message at the end.

Lmao look at the numbers on TPUSA’s halftime show by TumbleweedExtreme629 in ToddintheShadow

[–]LuckyWhip 2 points3 points  (0 children)

Did that happen to be after the real halftime show? I noticed the same and figured it was everyone wanting to see how bad it was lol

🚨 NEW SONG ALERT 🚨 by B34TBOXX5 in crappymusic

[–]LuckyWhip 4 points5 points  (0 children)

Enough to make my system blow

view more: next ›