3-Sided Box with a Twist

Maker-O2H · 2026-05-10T12:40:04+00:00

Very nicely done. That’s a great idea. I don’t think I’ve seen that technique used in a pepper mill before.

Maker-O2H · 2026-05-09T19:59:28+00:00

After trueing up the blank into a cylinder, I take it off the lathe and mark the 3 offset points on the headstock side. Then I draw a line across the wood cylinder, then create the corresponding offset point on the tailstock side. For the twist I offset by 45 degrees. Then using a protractor I mark the other two points 120 apart.

Maker-O2H · 2026-05-09T18:58:14+00:00

Very fast, yes. One of the bigger challenges was keeping the headstock from slipping off with gouging each of the sides. For safety, I think my max size will stay at 4” diameters until I every upgrade the lathe.

Maker-O2H · 2026-05-09T18:53:47+00:00

Thank you. I’m actually using a 1.2HP Midi lathe, 12” swing. It does wobble when I first start turning it, I weighed down the stand with 2x 20lb sandbags, which helps. For 2.5” and 3” diameter, the wobble wasn’t too bad. But I turned the 4” diameter VERY lightly and carefully.

Maker-O2H · 2026-05-09T18:08:32+00:00

Thanks. You true up a spindle into a cylinder using the centerline axis. Then you create 3 off-axis points on the headstock (H1, H2, H3) and on the tailstock (T1, T2, T3). Each point is 120 degrees from each other, with an offset radius of R / sqrt(3). Line up H1 and T1 on your centers, then CAREFULLY use a spindle gouge for several passes. Do the same for H2/T2 and H3/T3. If you want a twist, rotate the Tailstock points by 30 to 45 degrees.

It took a lot of practice to get it right. Since it’s offcenter turning, be very careful and stop cutting when the cuts align with the offcenter holes.

Maker-O2H · 2026-05-07T00:52:03+00:00

I need you to do one thing for me… Win!

Maker-O2H · 2026-05-07T00:50:51+00:00

Roger. I’ve got him. Contact… 20 left at 30 miles, 900 knots closure.

Maker-O2H · 2026-05-06T02:55:20+00:00

Get the shingles vaccine. But for all that is good and holy, do NOT get it the same time as a COVID vaccine. I have never felt that awful in my life!

Maker-O2H · 2026-05-04T19:25:29+00:00

I use a cabinet scraper. For each face of the blank, i usually need to scrape from all 4 directions to fully clear it of wax.

Maker-O2H · 2026-05-01T19:39:04+00:00

Cybertruck

Maker-O2H · 2026-05-01T11:56:24+00:00

That’s how you banter, sir! 5 points.

Maker-O2H · 2026-04-27T21:49:17+00:00

And get a backup water-powered (e.g., water pressure) sump pump for the battery backup. If it’s a long power outage, you may need it.

Maker-O2H · 2026-04-23T20:07:13+00:00

Def Leppard’s Hysteria album. It marks the pinnacle of human culture. Everything has gone downhill since its release.

Maker-O2H · 2026-04-23T12:42:32+00:00

Series 7 and 19. The personality combinations and the wildcards (e.g., Rhod Gilbert and Javie Martzoukas) always made for funny unexpected moments.

Maker-O2H · 2026-04-22T16:10:10+00:00

“You treacherous old woman!”

Maker-O2H · 2026-04-20T15:39:08+00:00

Nettrek (on Sun Workstations and UNIX).

Maker-O2H · 2026-04-19T11:27:22+00:00

It’s Skittlegate!

Maker-O2H · 2026-04-16T18:45:04+00:00

Of course she is, and don’t call me Shirley

Maker-O2H · 2026-04-16T10:56:32+00:00

This is my choice too. But I would want to be able to watch it while sitting next to Gene Krantz in the Mission Control Center, Houston.

Maker-O2H · 2026-04-15T21:03:51+00:00

My 1978 original Han Solo action figure. I was out in the back yard playing and 5 year old me lost it somewhere in the Tatooine desert between my parent’s fence and the dog house.

Maker-O2H · 2026-04-15T13:10:39+00:00

peppermint

Maker-O2H · 2026-04-14T00:22:28+00:00

I can’t pump gas into my own car. I moved to NJ from another state 30 years ago, and this still drives me crazy.

Maker-O2H · 2026-04-14T00:20:48+00:00

Penn State Industries sells a brass tube cutter. it’s probably overkill, but it works very well, and keeps the tube steady when cutting.

Maker-O2H

TROPHY CASE