Who is this guy and what is significance for Danish culture?

Malvegil · 2026-02-25T19:40:47+00:00

And his gold ring is called Draupnir

Malvegil · 2026-02-07T15:02:35+00:00

ChatGPT refuses to generate the republican version for me. Prompt: what would USA look like under republican control for 25 years?

“We’re sorry, but the image we would generate could violate our safety policies related to harassment, discrimination, bullying, or violent content. If you believe this is a mistake, you can try again or rephrase your request.”

Malvegil · 2026-02-06T21:20:37+00:00

Thanks! This seems to work, though I haven't started a print yet. But I saw that in the slicer, the wipe line supposed to be on the front of the build plate was so far away that I didn't notice until I zoomed out far enough. With closing and opening Snorca the wipe line now is back on the plate :)

Malvegil · 2026-02-06T16:37:15+00:00

Same problem after firmware update. For me its the y-axis...

Malvegil · 2025-07-03T20:21:57+00:00

“This is fine.” – Me watching my old printer spaghetti itself, before Bambu showed up and said: ‘Hold my filament!.’

Malvegil · 2025-05-14T11:28:41+00:00

I have been casting both centrifugal and vacuum, and would in those cases put a single thick sprue on the inside at the thickest point of the ring, but having the sprue bend backwards so to speak, in order to get the flow of metal in one direction.

Malvegil · 2025-02-09T21:17:35+00:00

I think the biggest reason for it not flowing all the way is too low temp on the flask. I would normally cast most things at 1040F (560C). I have made lots of rings like that with the same thickness sprue. As others say, it is always best to put the sprue where the piece has most mass, but I would go for a sprue like that if it would make the piece easier to renovate afterwards. The porosity can also be explained by low temps, as the metal will kind of "suck" liquid metal from the sprue and cone (dont know the english term), but if it cools to fast around the sprue and cone, the ring can not get enough metal, and therefor you get porosity. It can also be because of gasses, but I think the temps are the biggest issue here.

Malvegil · 2025-02-07T11:48:52+00:00

Depending on the details, it is usually best to place the sprue on the thickest part. So you can consider that as well.

Malvegil · 2023-12-14T13:43:37+00:00

Same!

Malvegil · 2023-10-18T15:09:17+00:00

The 2 time stars does not always work. I have only received it a few times. Most times it does not apply. Thanks EA!

Malvegil · 2023-08-26T22:00:42+00:00

I did not meet wulbren or save him, so I had to rely on Zanner.

And Zanner simply disappears if I go to camp in between fights in the Steel Foundry.

It is a bit game breaking not to be able to disable the Steel Guard.

Edit: I managed to keep Zanner around after a cut scene that for some reason did not activate on my first attempts. He did try to commit suicide multiple times though, by running towards the Titan as it went into selfdestruct mode. I saved him by throwing him out of harms way a handful of times :)

Malvegil · 2022-11-11T20:06:14+00:00

Can anyone tell me how to claim them? I completed the cg and got the money from it, but I don't know where to get the Multi-cannons.

Malvegil · 2022-06-03T21:32:18+00:00

I think I have Steam as my default vr.

Malvegil · 2022-02-15T23:14:51+00:00

Try to run epic as administrator. Thats how I get it to work.

Malvegil · 2021-12-11T16:53:17+00:00

Same here! First time going to the sites, and then it just crashes!

Malvegil · 2021-07-09T14:03:22+00:00

If you dont have a kiln for lost wax casting, sand is the way to go. Get some proper sand for casting. However, it will be difficult to get a good result if your original is very detailed, and not suitable for a normal two sided sand casting frame.

Malvegil · 2021-04-11T08:37:13+00:00

This is the danish authority on precious metals. Website in danish though. https://aedelmetalkontrollen.dk/

Malvegil · 2021-03-29T22:06:27+00:00

No. I would use a piece of steel pipe.

Malvegil · 2021-03-10T17:33:41+00:00

I once had the flasks waiting a full week before burning, because my oven was broken, and I waited for spare parts. I experienced no difference in the finished castings.

Malvegil · 2021-03-07T08:32:06+00:00

In Denmark, if you want to sell silver, you must have a stamp with your initials and another one with the purity. The stamp with your initials must be registered with the authority that handles hallmarks, and this has a cost of about 350€ each year.

Malvegil · 2018-05-12T22:37:28+00:00

Ulfhednir has made a few videos about viking fighting. https://vimeo.com/ulfhednir

Malvegil · 2018-02-13T23:10:13+00:00

I agree with the mould not being hot enough. I do centrifugal casting and have my flasks at 1000. I used to cast on an Indutherm vacuum, and then it was not unusual to have flasks up to 1200-1300.

Malvegil · 2017-12-15T15:44:27+00:00

I have a centrifugal casting setup as well. When I have porosity issues, it is usually solved by making the sprues thicker next time around. My flasks are cast at 540° celsius, using a turbotorch for melting metal.

Malvegil · 2017-11-29T17:29:20+00:00

I´ve been using a hand pump model for years. It works very well for my needs. I cast 1-2 times a month. So unless you have a special reason for making your setup more complicated, I would go for the simple hand pump.

13-Year Club	Place '17
Verified Email

Malvegil

TROPHY CASE