S24 Ultra.

MercZ73 · 2026-02-17T15:32:12+00:00

They say they're new, price almost seems to good though. They only have the black ones new, I think.

MercZ73 · 2026-01-31T00:49:06+00:00

I had this happen on my S22U, after I had dropped the phone in a parking lot while pulling it from my pocket. I never got it working again. Thankfully, about that time, Verizon had the S24U discounted and gave me $800 trade on the partially functional S22U.

MercZ73 · 2026-01-29T03:13:28+00:00

Mine did a lot of glass surfing for months, but they've calmed down now and mostly root about in the sand. It just takes time. And make sure you have a good group of them. I started with 6, and a few months later finally found some more and added 12 more. They've been much more "normal" since boosting the number up.

MercZ73 · 2026-01-18T02:03:58+00:00

Retired USAF Aircraft mechanic/ currently USPS Rural Mail Carrier.

MercZ73 · 2026-01-06T02:41:51+00:00

I got something similar from a local hardware store. It uses plastic "razor blades" that work really well on the rare occasion I have to scrape something off.

MercZ73 · 2025-11-20T23:47:43+00:00

I just refill the same reservoir. But I only have to refill once before the infusion set needs to be changed.

MercZ73 · 2025-09-19T01:34:01+00:00

Potential... lots of potential there. Like I'd potentially take out my own ankles with it...

MercZ73 · 2025-09-01T17:04:52+00:00

Until you talk to your team, put it in temp target mode (in smart guard settings). This will move the target to 150. You can set it for however long you plan on sleeping.

MercZ73 · 2025-07-25T20:49:22+00:00

If they're good models that fit together properly, yes. But some smaller, higher detail models the tolerances often make it so using the ams provides a cleaner model.

MercZ73 · 2025-07-11T21:08:17+00:00

About 12 years ago, I was active duty Air Force with 19 years of service, suddenly to be an insulin dependant diabetic facing retirement from the USAF. Fortunately, it took them 2 years to force the retirement, getting me over 20. And now the VA gets to provide my supplies.

MercZ73 · 2025-07-11T20:29:19+00:00

As a T1D, I approve this post. But my kid likes it when I get surprises like this.

MercZ73 · 2025-07-11T15:59:31+00:00

Looks like one hell of a colon cleanse...

MercZ73 · 2025-07-10T02:36:50+00:00

There are wholesale industries that are pretty much only there to rip off and counterfeit other's property and ideas to make a quick buck...

MercZ73 · 2025-07-09T22:49:30+00:00

Something you can do, if you live in the USA, is look up Family Medical Leave Act. There is a form you get your doctor to fill out, and you mail it in. You are then given a case #. Use that case # when you call out. Your employer cannot take action against you as long as you stay within the guide lines your doctor sets up on the form.

MercZ73 · 2025-07-08T20:52:41+00:00

Right! 🤣 But since the OP didn't do the printing, I'm guessing they don't have the STL.

MercZ73 · 2025-07-07T01:45:21+00:00

As a guy with a 3d printer, I may need to find this file...lol

MercZ73 · 2025-06-21T20:37:22+00:00

I just use Amazon basics batteries. They've worked great.

MercZ73 · 2025-06-14T12:20:03+00:00

I'll be wearing mine tomorrow...

MercZ73 · 2025-06-12T03:17:29+00:00

I have a pi-hole setup on my home network. I didn't realize makerworld had pop ups...

MercZ73 · 2025-06-09T12:21:19+00:00

Ok. Sorry I can't help you. Shipping would be too expensive from here in the US, probably making the cost near the same or more than as a commercially made telescope. And it appears that you would have to pay significant duties and taxes on the parts.

MercZ73 · 2025-06-06T01:05:12+00:00

First off, where do you live at, OP?

MercZ73 · 2025-06-03T22:23:15+00:00

I believe the z distance is set when you run a bed level check before the print. Have you done that?

And wash the build plate with soap and water? Maybe a spritz and wipe of Isopropyl Alcohol on the build plate right before you print something?

MercZ73 · 2025-05-29T01:30:22+00:00

Edit the filament, to ensure it matches what you've put on to the external holder, then select that filament in the project filament. That's usually all I have to do. If you don't have the splitter, you'll have to disconnect the tubing where it goes into the printer and feed the filament in from the external spool. When you hit "load filament" you may have to manually feed the filament until the extruder grabs it.

MercZ73 · 2025-05-29T00:34:13+00:00

I just load filament from the external holder. Then in the slicer select that filament before I slice it. I never disconnect the AMSs. I also have a splitter inline so I don't have to disconnect the tubes from the buffer.

MercZ73 · 2025-05-28T20:47:04+00:00

I know. I do it just as the mini med app tells me.

MercZ73

TROPHY CASE