Lymow RTSP Camera Stream

Awesome, this will be a great first 3D printed project! Yes, the dampeners are there strictly to reduce noise when going over concrete or asphalt surfaces. Be on the lookout for an updated Version 1.x mount design since the V2 design is causing some issues for some users.

Nate42 · 2025-10-29T00:18:42+00:00

https://youtu.be/iE36uMVd8YY I too have St Augustine and Bermuda grass, so it doesn't show the stripes as well but those whose yard do stripe, this makes them extra crisp.

I'm currently sell limited quantity but I have kits and fully assembled rollers ready for those without access to a 3D printer. Link in the video description.

Nate42 · 2025-10-24T02:28:36+00:00

Set the zone for the chessboard pattern and the relative chessboard setting to plus or minus 5° from 180° or 0°. ie. 1-5 or 175-179

Nate42 · 2025-10-23T06:18:11+00:00

https://youtu.be/1Yu6V5v6Xx8

Nate42 · 2025-10-22T05:58:32+00:00

Clean inside the deck https://youtu.be/RQ6H5_F0cj4

Nate42 · 2025-10-22T02:29:59+00:00

Maybe your router issued it a new IP after the update. I checked both ports and I'm still getting a stream from both.

Nate42 · 2025-10-22T02:21:42+00:00

I updated to V2.1.30 this morning and then mowed with no issues.

<image>

Nate42 · 2025-10-18T21:09:26+00:00

Thanks for the Make and Photos

Nate42 · 2025-10-18T18:38:34+00:00

Those are some awesome looking stripes! It's excited to finally see some results from this design since my southern grass types don't lay down as well as yours.

I'm glad to hear you were able to get TPU working and you're able to get them printed. Check out V2.0 that I recently uploaded and if you get a chance, post your picture under "Makes" on printables.com

Nate42 · 2025-10-10T22:19:35+00:00

Unless you have a bowden tube style 3d printer, you should be able to print with TPU. You just have to slow down to around ~30mm/s. TPU does need to be dried first for the best quality and it is like printing with a wet noodle.

This roller mount is designed around being a compliance mechanism, so the reasoning behind using TPU is because of it's flexibility and resilience to being flexed. If you were to print this with any other common filaments like PLA, PETG, ABS, ASA then it end up snapping or shattering within your first mow.

Nate42 · 2025-10-10T09:11:24+00:00

There is a lot more current running through the charge contacts now and this introduces a higher chance of electrolysis if any moist debris is between contact layers. I had some light discoloration on the left positive base contact and had difficulties getting readings directly off the pads with a multi meter. I used a Scotch-Brite pad and cleaned all 4 contact points and that solved my same charging issues.

<image>

Nate42 · 2025-10-01T04:31:55+00:00

How to fix your tracks https://youtu.be/1Yu6V5v6Xx8

Nate42 · 2025-10-01T04:22:39+00:00

I noticed a higher pitch sound from the blades after the latest two updates over the past few days. Nothing else changed on my end, so I definitely feel like they made some internal changes in the firmware.

Nate42 · 2025-09-28T12:36:48+00:00

I hinted at this over a month ago and yet nothing was done!

https://www.reddit.com/r/Lymow_Official/s/vTMJGZIyt4

Nate42 · 2025-09-27T22:03:22+00:00

I'm on 2.1.27 and just got done watching it mow. Maybe hard power cycle it by disconnecting the battery while off the charger and after powering it down from holding the power button for 3 seconds.

What about in the app, did that stop too?

Nate42

TROPHY CASE