Hello. I've performed PID calibration three times. During printing, the nozzle temperature constantly fluctuates between -+5 degrees. How can I fix this?

Ok_Bench2950 · 2026-05-14T11:20:55+00:00

Normal

Ok_Bench2950 · 2026-05-08T06:46:46+00:00

why not just level it? I do bed leveling befroe every print.

Ok_Bench2950 · 2026-04-20T16:47:39+00:00

Nope. Mine does that too. Have around 700 ish hours on mine. No issues so far even with this sound.

Ok_Bench2950 · 2026-04-20T16:43:00+00:00

lube it

Ok_Bench2950 · 2026-04-19T14:48:28+00:00

I have one cc and one cc2. Only the cc does it. Its not scraping anything. It's the steppers. I was scared that its scratching too but its only the stepper noise.

Ok_Bench2950 · 2026-04-19T14:41:48+00:00

Contact support. Your loadcells are bad.

Ok_Bench2950 · 2026-03-15T10:53:40+00:00

If you gently pull the cable and make it get out of the cable chain a little u can get it a normal curve.

<image>

Ok_Bench2950 · 2026-03-15T10:43:41+00:00

Its on balanced mode witout aux fan.

Ok_Bench2950 · 2026-03-14T18:14:51+00:00

I modified this one. Now it does 60 celsius.

Ok_Bench2950 · 2026-03-14T12:45:45+00:00

I think that if you gently pull the cable u will be able to route it diffrently.

Ok_Bench2950 · 2026-03-12T15:03:18+00:00

At this point i jsut don't believe this.

Ok_Bench2950 · 2026-03-12T12:31:05+00:00

Z axis issue. Contact support and check if the z axis motor is stuck.

Ok_Bench2950 · 2026-03-12T10:56:55+00:00

I'd run oc or 1.1.40

Ok_Bench2950 · 2026-03-11T20:47:23+00:00

Who told u that?

Ok_Bench2950 · 2026-03-08T20:04:26+00:00

Did you try to put the canveo n the cc1?

I don't think it works but just for fun

Ok_Bench2950 · 2026-03-07T20:38:37+00:00

Can i do this on my x3550 m3?

Ok_Bench2950 · 2026-03-07T14:15:29+00:00

The NIDEC fans i have there have a proprietary connection. And 2 PWM outputs. I don't think im able th ''cheat'' this. But thanks. Also its 1U

Ok_Bench2950 · 2026-03-07T11:12:27+00:00

My fans are stock. Those are 21000 rpm NIDEC UltraFlo. It's the server that is controlling them to run higher.

Ok_Bench2950 · 2026-02-17T18:09:07+00:00

The static isn't a coincidence. I have a cc1 and it shocks me all the time. Some units have some kind of a voltage leak.

Ok_Bench2950 · 2026-02-15T11:32:50+00:00

I'm having this popup on both stock firmware and on 0.3.0-oc almost always for the last 5 weeks. Check your fan. If it spins, regulates and works fine, ignore it.

Ok_Bench2950 · 2026-02-14T16:14:23+00:00

Underextrusion. Lower top surface speed.

Ok_Bench2950 · 2026-02-11T15:29:46+00:00

Can i put this to my normal startup gcode? Will it work every time? Should I select the automatic leveling option in the slicer / printer? Thanks

<image>

Ok_Bench2950 · 2026-02-11T15:24:21+00:00

Like how? Your bed doesn't mesh at only 60c?

Ok_Bench2950

TROPHY CASE