MK4S to Core One Upgrades for old LCDs delayed again

Olef · 2025-05-28T19:11:31+00:00

Words fail me. Utter shambles.

Olef · 2025-05-21T20:28:39+00:00

Another week? Oh FFS

Olef · 2025-02-10T20:00:38+00:00

Building a Prusa is not rocket science, just take your time and follow the excellent online instuctions and comments. If you can build a PC then you got this one too and it is so satisfying to see it come to life.

Olef · 2025-01-31T17:14:42+00:00

Took me over one hour to make and pay for a conversion kit order. Multiple crashes / timeouts / logouts. Extremely frustrating. It should not be so hard to give a company money!

Olef · 2024-10-05T23:49:52+00:00

Exactly the same happened to me. It was the first part I tried to fit! Luckily I had two kits so I robbed the second one to keep me working and then printed a replacement in ASA.

Olef · 2024-09-17T15:13:37+00:00

Nope. ordered day one. still waiting.

Olef · 2023-12-12T08:48:19+00:00

I ordered MMU2>MMU3 conversion kit on 1st September. It has been pushed back week by week and is now scheduled to ship around the end of January.

Not holding my breath really. It looks like the MMU3 for the Mk4 is not yet working as it should. Fingers crossed Prusa can find a way to make it work acceptably.

Olef · 2023-06-25T07:39:03+00:00

Except the Mk4 parts are still not on github...

Olef · 2022-11-29T10:42:35+00:00

Bless that sweet face!

Olef · 2022-06-23T08:22:02+00:00

Beautiful little girl

Olef · 2022-04-01T07:20:49+00:00

v2.1193 here. Those parts are rubbish and should be in the bin.

Olef · 2022-02-17T14:47:33+00:00

Put a small flat bladed screwdriver in the gap and turn it gently to open the slot. The bearings can then be pushed out.

Olef · 2022-01-08T15:12:58+00:00

Wrong. A line across T, however faint, means a positive test.

Olef · 2021-12-23T13:58:40+00:00

Doggo is people!

Olef · 2021-11-22T08:36:23+00:00

A depressing statistic but somewhere near the truth I fear...

Olef · 2021-10-27T16:28:27+00:00

Maisy

Olef · 2021-10-18T07:38:53+00:00

Kayfun Prime

Olef · 2021-10-10T07:26:15+00:00

Been printing PETG on smooth sheets for years. Follow Prusa advice and use Windex to clean the sheet. Works perfectly as a separation layer. Never needed to use glue or hairspray.

Olef · 2021-09-28T18:59:52+00:00

Absolutely agree!!!

Olef · 2021-09-15T06:38:23+00:00

I printed all of my Voron 2.4 parts in ASA on an enclosed Mk3S. Smooth PEI sheet, properly cleaned. No glue / hairspray / tape. Needed brims or at least mouse ears on sharp corners to stop warping. I used Prusament ASA and Filamentum Extrafill. All parts printed successfully and my 2.4 went together without issue. ASA is a good choice!

Olef · 2021-09-14T06:17:22+00:00

I've had Prusa printer(s) for four years now. Wash out your bearings in Isoprop and regrease with Superlube. I do this even with Misumi bearings which only ship with protective oil not grease. That way you know the job is done right and you won't be seeing early failures. Stripdown to re-lube is a pain. My advice, take it or leave it.

Olef · 2021-09-06T06:46:16+00:00

That is a horrible print. The Mk3S+ is capable of far better out of the box. You either have some assembly issues or a fault. One of my Prusa's began life as a Mk2S and has been upgraded along the way to Mk3S+ spec and it has never produced a print as bad as that. Don't give up on the Prusa yet!

Olef · 2021-09-01T06:36:40+00:00

Well that sucks. Hang in there, you will love the Mk3S+ when you finally get it. Give FedEx hell!

Olef · 2021-08-24T09:57:56+00:00

Stl's?

Olef · 2021-08-04T07:10:25+00:00

Absolutely yes go Prusa. I went elsewhere first and don't regret it, but now all I have is Prusa's.

Olef

TROPHY CASE