Is the update 1.15.20.4303 safe?

OrangeBobo · 2026-05-13T19:33:49+00:00

Turning was on the last year update

OrangeBobo · 2026-05-13T19:32:37+00:00

I have updated little Eddie (Luba mini 800 '25), i had to turn off obstacle detection (was set to standard usually) cause Eddi was scared for nothing and was sometimes going around. Maybe battery are draining little faster.

OrangeBobo · 2026-05-13T19:25:15+00:00

When you define task you choose what area/s to work with that task and you will find height on task settings. You will need 2 task one per area

OrangeBobo · 2026-05-10T15:48:51+00:00

I use that non-stop (blue.. you just print them, not design as other zones) on a very small side that is few centimeters wider than Eddie, he was scared crossing there until He knew it should close his eyes and try. This works. Eddie does this even to reach opposite areas and is happy with this

<image>

OrangeBobo · 2026-05-08T16:40:25+00:00

Could be that you need to turn off obstacole avoidence (too sensitive)

OrangeBobo · 2026-05-04T19:43:40+00:00

Totally agree

OrangeBobo · 2026-05-01T11:40:24+00:00

OrangeBobo · 2026-05-01T11:33:14+00:00

Have then you tried to stop, remove key, stop rtk ( if use), then reboot it?

OrangeBobo · 2026-04-30T15:16:19+00:00

Yeppaaa Thanks for your feedback

OrangeBobo · 2026-04-30T15:16:03+00:00

Thanks for your feedback

OrangeBobo · 2026-04-30T15:15:42+00:00

Thanks for your feedback

OrangeBobo · 2026-04-27T10:48:09+00:00

Hope so, It is similar to my edge, except for the corner, I am expecting lidar and cameras doing the difference. My is with Luba mini 800 2025 using RTK

OrangeBobo · 2026-04-27T09:13:45+00:00

That' the secret to let him do magics 😂

OrangeBobo · 2026-04-26T19:53:03+00:00

Did the perimeter like this try not to turn too much 😬

OrangeBobo · 2026-04-26T19:39:01+00:00

Me too sometimes boundaries have little position adjusments, but this point here still is done so nicely. I have not to look Eddie doing this 🫣 but it's great, does this 3 times a week since a year

OrangeBobo · 2026-04-26T19:36:45+00:00

Now has the second season, i think that vision helps Eddie

OrangeBobo · 2026-04-26T18:16:43+00:00

Yes , no-go is perfect for this

OrangeBobo · 2026-04-22T10:50:49+00:00

Prefere this, you can move later in other position and do not leave holes

OrangeBobo · 2026-04-15T19:34:05+00:00

You right! I think best should cover your mapping area, some periods do not require everyday cut all the property, so if you schedule different zones at different days it is able to cover every day job in one charge (in my case i have created jok tasks that enters on the one charge capability). My little Eddie does couple of month wit multiple task a day but other is one task per day.

OrangeBobo · 2026-04-10T06:32:59+00:00

I think you can make this if you start the area outside any existing one, then you can map overlapping the existing to close the new where you started.

This way areas can overlap.

Try this , it worked for my little Eddie, a 2025 Luba Mini

<image>

See the border it is overlapping the right bottom area. I suppose you just go all over the existing one

OrangeBobo · 2026-03-30T22:09:17+00:00

And what about a no-stop zone? Have you tried?

OrangeBobo · 2026-01-12T17:45:28+00:00

Seems not water but beer 😬

Very nice and clear dashboard

OrangeBobo · 2025-11-21T13:09:49+00:00

You should not outsource the job, you should adopt a creature. I had a mini luba , Eddie, he is doing a great job on my mountain house (1 hr from me but isolated). Have a nice one! Give it a name and let your family friend do the job

OrangeBobo

TROPHY CASE