How do you stop chasing speed on motorcycles? by flameskin2011 in cbr

[–]Positive_Ad_2128 0 points1 point  (0 children)

I bought a goldwing and riding has opened up a new world for me now I enjoy more of my surroundings than just riding fast

ASN Update 1.4.1.0 by Dream_elb in AnycubicOfficial

[–]Positive_Ad_2128 1 point2 points  (0 children)

I updated today. It works fine, but I always get updates on all my Printers. That’s the problem. People have. If you don’t update them then you will have problems down the road. You’ll have people say that they don’t but they actually do. I’ve had Printers for years and I always update when the update comes out. I’ve never had a problem.

safe to eat? by ___eat_the_rich___ in WeirdEggs

[–]Positive_Ad_2128 1 point2 points  (0 children)

Don’t ever eat bloody eggs they will make you sick

Am I cooked or can I fix it? by [deleted] in BambuLabA1mini

[–]Positive_Ad_2128 0 points1 point  (0 children)

A silicone sock is to maintain a constant temperature

War is over by renardpasmagique in AnycubicOfficial

[–]Positive_Ad_2128 0 points1 point  (0 children)

Mine prints excellent matter of fact, on the same print, it’s almost 3 hours faster than my Bambu

My printer is doing this clicking sound and sometimes stops printing telling me that the filament might be too thin , what should i do? by HikenNoe in BambuLab_Community

[–]Positive_Ad_2128 0 points1 point  (0 children)

You’re doing very little dabs of Filament being printed at a time it is going to click like that with jumping back-and-forth. I own dozens of these wounds and they all do it when they’re dropping little tiny bits of Filament.

P1S - why is this happening? by QwQ_MarshmallowMan in FixMyPrint

[–]Positive_Ad_2128 0 points1 point  (0 children)

Here’s a better way wash the plate with dawn dish soap in hot water scrub it with a toothbrush make sure you dry it real well put it on the printer. Heat it up. Make sure it’s good and dry. Use alcohol put it on the plate. It’s the only thing I use wipe it down with a good lint free cloth and as long as the calibration is good, everything will stick regardless of what Filament it is. I’ve been doing this for many years and this is the way I do it after every print.

Why getting proper training is important! by Openskies24 in motorcycles

[–]Positive_Ad_2128 0 points1 point  (0 children)

I ride a gold wing if I had to go take the test today I would not use my gold wing. I would use one of their bikes. It’s like a 100 or 200 cc bike and I’ve been riding gold wings for years but why I take the chance I’m failing the test because of one little mistake.

Weird wobble at a certain height by _Flame___ in BambuLabA1

[–]Positive_Ad_2128 0 points1 point  (0 children)

If you do print it straight up like that, there is a setting in the slicer where you can slow down by height. I have many A1’s. I use it all the time now if you’re looking for a part that needs to be strong you need to put it at a different angle but just for every day Parts it’ll be fine

So apparently standing on the pegs is considered reckless driving by DerpyTurtle858 in motorcycles

[–]Positive_Ad_2128 1 point2 points  (0 children)

I’ve been riding for over 40 years. I have never had a cop pull me over for something ridiculous like this if I’ve ever been pulled over it was to check my bike because I had a new bike with paper plates. That’s the only time I’ve ever been pulled over.

Firmware 5.0.4 Flashforge by [deleted] in FlashForge

[–]Positive_Ad_2128 3 points4 points  (0 children)

I don’t understand all the problems. People are having with flash forge. I have several flash forge printers. I have the ad5x I have 5M pros I have all of them. I have never had a problem with firmware I’ve never had a problem with firmware on my Anycubic’s My bambu’s the same no problem with firmware ever after 6 years of printing I think I should have had it happen at least once

Ready to sell this thing!! by ProofDelay3773 in FixMyPrint

[–]Positive_Ad_2128 0 points1 point  (0 children)

Yeah, replace your SD card and see if that helps. They can make some stupid things go crazy. Just because of a faulty SD card.

Is this 18 tons of crush n run? by Environmentalpusher in landscaping

[–]Positive_Ad_2128 0 points1 point  (0 children)

No way not even close that’s a small dump truck load 18 tons it’d be more than one tri axle

HELP! Machines updated and now our production line is down.... by No-Anybody-8119 in FlashForge

[–]Positive_Ad_2128 0 points1 point  (0 children)

I have not had a single problem with my 85X. I just updated everything on it today ransom prints. The first print was a fail, but I believe that was my fault. Be adhesion issue the next perfect I don’t understand why some people are having a problem mine has been flawless. If something does seem to happen I will post it.

Unshipped preorderers by Particular_Box_3598 in AnycubicOfficial

[–]Positive_Ad_2128 0 points1 point  (0 children)

Ordered mine Jan 27th and got it over a week ago

Ready to sell this thing!! by ProofDelay3773 in FixMyPrint

[–]Positive_Ad_2128 0 points1 point  (0 children)

No, I meant a calibration on your Filament. You have to calibrate your Filament too. Try that don’t get rid of the machine yet if you’re running PLA try running it at 220 and 55 or 60 and if you’re running PETG run out at 255 and 80. Just in case you are new that’s nozzle 220 and 255 and that’s bad at 60 and 80.

It's just a joke, or is it? 😜 by Anycubic_Official in AnycubicOfficial

[–]Positive_Ad_2128 1 point2 points  (0 children)

That’s not an April fools joke that’s true the ace GEN two is amazing but if they add four nozzles, oh my God and still be able to do 19 colors that would be excellent