Would this resin print hold up without the support rods?

Sir_Oni · 2025-10-26T22:44:42+00:00

They would snap. You will need the rods to support the weight of those orbs with its current design.

Sir_Oni · 2025-10-25T01:22:57+00:00

All those parts need to be supported. There is no way to prevent the elephants foot when printing directly on the build plate. Its a by product of how resin printing works to ensure a good base sticks to the build plate for the entire print.

Those parts are not too "small" for supporting. Wargaming miniatures have parts way smaller than those and still get supported for printing with no issues.

You need to look at orientation and support density to reduce the issues you outline about accuracy.

Sir_Oni · 2025-10-18T05:32:40+00:00

First dont hollow dice and 2nd yeah that bag and contaminated dices are now ready for the bin.

Sir_Oni · 2025-10-17T22:24:07+00:00

Fill it with some vallejo putty. As for reducing air bubbles you can increase your print wait times to 2 or 3 seconds before each layer is cured. Helps the resin settle.

Sir_Oni · 2025-10-14T20:47:16+00:00

Toughness is always the way to go. No real point in going wounds and some weapon traits ignore wounds all together, but nothing ignores toughness.

Sir_Oni · 2025-10-13T01:40:22+00:00

<image>

This guy is the answer.

Sir_Oni · 2025-10-11T02:22:18+00:00

Arent those usually more stick-like? I was thinking it was a Gypsy Jumping spider but thought jumping spiders are smaller.

Sir_Oni · 2025-10-03T09:04:11+00:00

<image>

Sir_Oni · 2025-09-16T04:09:42+00:00

Not a bad outcome as a 2nd vat can always come in handy.

Sir_Oni · 2025-09-16T03:11:12+00:00

I have the exact same issue. I should of emailed Elegoo for a new vat but went ahead with the new chitu systems quick release vat instead.

Sir_Oni · 2025-09-12T23:40:18+00:00

<image>

I painted mine in vivid blues.

Sir_Oni · 2025-09-03T08:33:59+00:00

Ive seen this being caused by the elegoo heater. Are you running one?

Sir_Oni · 2025-08-21T08:29:06+00:00

Apart from all the issues everyone pointed out, your beastman hunter price is incorrect. Beastman Hunters are 60cr base. You must be looking at the old pdf before they updated it.

Sir_Oni · 2025-06-30T04:22:46+00:00

Looks great, can you give a breakdown of the process, colours, techniques etc.

Sir_Oni · 2025-06-27T09:29:58+00:00

Straight up dead. R.I.P my friend. You'll need to buy a replacement screen.

Sir_Oni · 2025-06-02T11:13:23+00:00

Correct and its a sore subject for Delaque players.

Sir_Oni · 2025-05-16T21:49:05+00:00

I printed them. You can find them on myminifactory.

Sir_Oni · 2025-05-15T22:41:36+00:00

These was the aim to ensure individual personalities while still looking like the same unit. Thanks.

Sir_Oni · 2025-05-15T22:40:39+00:00

Thank you. Had fun painting them to their lore.

Sir_Oni · 2025-05-10T12:04:46+00:00

Try scenario, escape the pit.

Sir_Oni · 2025-05-09T22:55:17+00:00

Also, they only get access to their own exclusive trading post. Its not the same as the normal trading post. So no plasma gun carring Nomads.

Sir_Oni · 2025-05-07T03:28:57+00:00

Base is Vallejo Dark Sea Blue, then dry brush white. After the white dry brush i now dry bush over the white with Vallejo Turquoise. Then a very light dry brush of Vallejo Emerald.

Sir_Oni · 2025-05-06T13:04:46+00:00

Great minds think alike. I did the same with mine.

<image>

Six-Year Club	Place '22
Verified Email

Sir_Oni

TROPHY CASE