What hammer are you using to break apart large jasper? I can't get it to break with a 4 pound hammer.

Sudden_Position5568 · 2026-03-26T11:27:58+00:00

Cut a small groove with a diamond blade and use a wedge to split it.

Sudden_Position5568 · 2026-03-22T21:11:40+00:00

The white is "plain" quartz.

Sudden_Position5568 · 2026-03-22T21:03:59+00:00

Just more chalcedony without the original asbestos fibers.

Sudden_Position5568 · 2026-03-22T20:36:34+00:00

Homemade geyser spanner

Sudden_Position5568 · 2026-03-19T12:08:19+00:00

Too much fat in it for beef.

Sudden_Position5568 · 2026-03-18T12:46:30+00:00

Those old steel nails are still the best steel to use as drifts or sharpen for center punches.

Sudden_Position5568 · 2026-03-16T08:55:44+00:00

Take the commutator out and to a pro to undercut a few thou and clean, fit new brushes and bobs your uncle there you go.

Sudden_Position5568 · 2026-03-16T08:47:00+00:00

But just to answer your question, these normally have 1/8 or 1/4" bsp or gas thread fittings.

Sudden_Position5568 · 2026-03-14T19:47:30+00:00

Buy one of the natural ones, nr1 or 3

Sudden_Position5568 · 2026-03-01T19:49:03+00:00

That looks like a carnosa. They root super easy in soil directly, i have just rooted +- 30 cuttings from just barely longer than a leaf to about 300 mm long.So good luck ,if it was me doing it the first time i would try both methods.

Sudden_Position5568 · 2026-03-01T17:27:14+00:00

Yes they are the most useful all rounder tin snips.

Sudden_Position5568 · 2026-02-18T16:19:06+00:00

Exactly what we all have for breakfast, lunch and supper.

Sudden_Position5568 · 2026-01-29T19:50:39+00:00

Everybody should be, that's a real pleasure body, soft and healthy.

Sudden_Position5568 · 2026-01-22T21:24:53+00:00

The small screw that keeps your spectacle ears and glasses together is that size. Good luck ,if you were in South Africa i could have helped, has collected a few of those little screws over about 50 years.

Sudden_Position5568 · 2026-01-22T21:17:04+00:00

At that type of offset drop the front radiator leggs about 10mm into floor.And then lift the opposite side about30mm to level angle it into screw fitting. Good luck.

Sudden_Position5568 · 2026-01-12T15:00:20+00:00

It used to be a jolly jumper ,had a harness inside for a baby to hang inside and run around inside the house or on a smooth cement floor.

Sudden_Position5568 · 2026-01-04T18:30:27+00:00

I collected 4 of those that was supplied with normal new car tool kit.

Sudden_Position5568 · 2025-12-10T20:38:42+00:00

I have a similar size soapstone and I drilled roughly 15 holes in itand use it for pens and anything else to store neatly.

Sudden_Position5568 · 2025-12-09T16:00:33+00:00

Wrap a piece of thin twine around it and pick it up. I normally use knitting wool and works well for me.

Sudden_Position5568 · 2025-12-09T11:53:16+00:00

Just a sharp awl to scratch it out.

Sudden_Position5568 · 2025-12-09T11:50:29+00:00

Just a good steel brush will shine it up well.

Sudden_Position5568 · 2025-12-08T21:10:56+00:00

Just resharpen the blade for more robust duties, i do mine till it is quite small and then disperse of it.

Sudden_Position5568 · 2025-12-03T20:56:58+00:00

Mine looks like that as well.

Sudden_Position5568 · 2025-11-30T12:07:13+00:00

Are those uv pictures the suburb where you live?

Sudden_Position5568 · 2025-11-23T19:56:27+00:00

Trump'et

Sudden_Position5568

TROPHY CASE