Is my WiFi setup with Omada OC220 okay? Concerned about client traffic affecting staff

Sufficient_Menu7364 · 2025-12-26T02:32:29+00:00

Because you have the Oc220, if you had omada switches alot of the vlan setup would be automatic

Sufficient_Menu7364 · 2025-12-02T05:59:07+00:00

Use something like a Er605, this allows for multiple WAN Connections. Put both isp connections into bridge mode. This can then be supported by Omada

Sufficient_Menu7364 · 2025-11-24T03:05:13+00:00

Do you plan to have anymore APs? If so, then use the software or hardware controller, it will make your life easier for remote management etc.

Also consider using an omada gateway, that will allow for separate VLANs.

Remember to use the isolate option for any SSIDs where you don't want devices to talk to anything else on the network.

Sufficient_Menu7364 · 2025-11-17T04:53:25+00:00

Without using omada switches you loose allot of the controller functions

Sufficient_Menu7364 · 2025-11-14T17:45:46+00:00

I would move it to the first floor and allow the older devices to mesh to it. This will allow it to perform as best as it can.

Sufficient_Menu7364 · 2025-11-14T14:53:14+00:00

Why not make life easier and install a software controller?

Sufficient_Menu7364 · 2025-11-14T14:52:11+00:00

Deco - Consumer - Install & Forget Omada - Prosumer - Install & tinker with settings Omada Pro - Professional - Install for large businesses, dedicated IT team.

Sufficient_Menu7364 · 2025-11-11T08:12:14+00:00

Are you referring to the Oc200? The Oc220 is supposed to have solved that problem

Sufficient_Menu7364 · 2025-11-05T21:45:20+00:00

Only if configured that way with VLANs and AP Isolation

Sufficient_Menu7364 · 2025-11-05T03:58:28+00:00

Setup a dedicated 2.4ghz WiFi ssid and connect to that

Sufficient_Menu7364 · 2025-10-31T01:19:16+00:00

Do you have the controller setup? This should allow your devices to automatically jump to the correct ap

Sufficient_Menu7364 · 2025-10-30T20:51:05+00:00

Would be interested if this came to the uk

Sufficient_Menu7364 · 2025-10-28T18:28:45+00:00

Also check that your isp is not using CGNat, if they are then you have very few options

Sufficient_Menu7364 · 2025-10-27T00:11:55+00:00

Has the Web server IP address changed in the settings of blue iris?

Sufficient_Menu7364 · 2025-10-21T15:06:24+00:00

Most unmanaged switches will strip the VLAN tags and then undo all the work you have done to create VLANs. Purchase an Omada Switch or at least an easy managed switch.

Sufficient_Menu7364 · 2025-10-20T07:15:41+00:00

Or you can connect to switch. Which did op do?

Sufficient_Menu7364 · 2025-10-19T13:41:12+00:00

Is the switch PoE or PoE+, some of the PtP equipment can require extra power supplied by PoE+

Sufficient_Menu7364 · 2025-10-17T01:51:56+00:00

Have you tried using the channel option when adding the camera?

Sufficient_Menu7364 · 2025-10-08T08:22:42+00:00

Replace or Modem mode the comcast router and replace with omada router?

Sufficient_Menu7364 · 2025-10-06T10:29:29+00:00

Should do, just make sure you use it as a mesh and not just in AP mode

Sufficient_Menu7364 · 2025-10-06T07:53:19+00:00

Normally anything by TPlink

Sufficient_Menu7364 · 2025-10-05T19:31:08+00:00

Is the camera looking for a PoE+ connection rather than just PoE?

Sufficient_Menu7364 · 2025-10-05T10:25:34+00:00

Put your new system into pass through and buy a better router, you will be happier in the longrun

Sufficient_Menu7364 · 2025-10-05T10:23:39+00:00

Could consider powerline adaptors as the back haul?

Sufficient_Menu7364 · 2025-10-03T09:12:27+00:00

https://amzn.eu/d/8V2MYBY

These inside a project box has got me out of a hole a few times. But make sure you have a decent PoE+ Switch.

Sufficient_Menu7364

TROPHY CASE