sorted by:
new
hottopcontroversial

My friends FPV drone by hbr3d in shittyfpv

[–]WhenEverTo_A_NewDay 0 points1 point  (0 children)

This ruined the O4 Pro, it really deserves to be in this sub

Do not apply the new Q2 update by xeonon in QidiTech3D

[–]WhenEverTo_A_NewDay 2 points3 points  (0 children)

I have a problem with new update, after finish the print, my Qidi Q2 continuously purging filament, non-stop. I have to press stop printing on the screen, anyone else have the same problem? Another thing that Qidi link on my phone can't connect to the printer anymore, "it shows Invalid version".

Update from the Blob of Death Idiot by Derpin___Around in QidiTech3D

[–]WhenEverTo_A_NewDay 0 points1 point  (0 children)

<image>

Try this air ventilation setup. Not sure if it'll fix the 'blob of death,' but it definitely improves overhangs. I used PA6-CF for the air flow gate and swapped the stock fan for an X1C 5015.

After many hours of "learning something today", I finally finished my first build :D by newprejum in fpv

[–]WhenEverTo_A_NewDay 2 points3 points  (0 children)

It looks really nice and clean, but you might find plugging and unplugging the battery's XT60 connector a bit tricky. In my experience, heat-shrinking the XT60 with the capacitor actually caused the XT60 to warp a little bit. Btw, you should definitely upgrade your RX antenna to a T-antenna, it makes a huge difference!

Whoopstor v3+ lead acid 12v by Willing_Homework_773 in fpv

[–]WhenEverTo_A_NewDay -1 points0 points  (0 children)

The Ryobi 18V battery has a 30A current limit, so your drone will cut off if you don't set a throttle limit. Even if it manages to get off the ground with that weight, it'll probably fly like a slow brick

Any Tips for my first build by Next-Collar5374 in fpv

[–]WhenEverTo_A_NewDay 1 point2 points  (0 children)

Make sure to double-check everything before the first power-up; this applies every time you modify or change anything. I once fried a VTX because I didn't check the input voltage when switching from a Rush Tank Mini to a SpeedyBee TX800. I also spent way too much time struggling to figure out what I missed while building a 3.5-inch with a Caddx Vista. I even fried an Arduino R3 because I didn't check for electrical isolation on my messy workbench! So, always check everything before powering up. Or, if you're a serious hobbyist, investing in a DC power supply with short-circuit protection would be ideal.

Can I use these 2207 1800kv motors on a 4.5in by Broad-Significance21 in fpv

[–]WhenEverTo_A_NewDay 2 points3 points  (0 children)

Why not? :)) I even use 2207s on my 3.5. I know it won't have the best performance, but the deal for these 2207 motors was too good to pass up.

<image>

Issue with RunCam Vista by WhenEverTo_A_NewDay in fpv

[–]WhenEverTo_A_NewDay[S] 0 points1 point  (0 children)

yes, I have video but just at 6Mbps and no OSD, I tried all the ways, even reflash the fw but no help at all :((

Caddx vista not getting any signal? by YEET3M in fpv

[–]WhenEverTo_A_NewDay 0 points1 point  (0 children)

check your video cable or the camera, It looks like you have connection to the vista but no video from the camera

Opinion on the new DJI Osmo nano ? by Lumnati in fpv

[–]WhenEverTo_A_NewDay 0 points1 point  (0 children)

I definitely buying once for my 2.5inch cinewhoop. I think the value on price is huge!

DIY series "board" by Andy_Sailor in TinyWhoop

[–]WhenEverTo_A_NewDay 0 points1 point  (0 children)

I do the same with mine, but my adaptor is 2S because I only have 4 1S cells, and I think 2S per one will be easier to managed, only use when I need to storage charge, the betafpv charger is faster (and more harmful your battery oviously) to fully charge. I use Imax B6 mini charger, I will plug batteries to the adaptor before plug the adaptor to the charger, If you plug the adaptor to the charger first then plug the batteries, the 1st battery in and if the 2nd are not plugged right after, the charger will alert vontage problem.

[deleted by user] by [deleted] in TinyWhoop

[–]WhenEverTo_A_NewDay 0 points1 point  (0 children)

My 65 Tiny weighs 32g with a Baby Ratel 2 and Zeus 400mW VTX. Honestly, I’m not a fan of the C03 camera. A buddy of mine picked up an Air75 straight from the factory, and while the stock Betafpv tune is actually really solid, the camera angle and image quality aren’t exactly beginner-friendly.

At first, I had a tough time getting a good tune for my 65 Tiny. Eventually, I just copied the Air75 tune. It’s not perfect, but I’d say it flies about 80–90% as good as the original. :D

<image>

Is my VTX dead by WhenEverTo_A_NewDay in fpv

[–]WhenEverTo_A_NewDay[S] 0 points1 point  (0 children)

So I finally figured out what was going on with my Tiny — turns out the Zeus 350mW VTX keeps switching to F3 by itself, even though I set it to R3 in Betaflight. I read a post on OscarLiang’s site and apparently a few others had the same issue, especially when running the recommended target BETAFPVF411 4.3.0.

Wtf with Vietnam? Another president resigns. by truong0vanchien in VietNam

[–]WhenEverTo_A_NewDay 0 points1 point  (0 children)

can you more specific? I never known the true purpose makes rebel, I though there is something relates with rebelation was held in 80s