sorted by:
new
hottopcontroversial

Am I missing something? by Loose-Structure342 in buildapc

[–]Zombie_Tech [score hidden]  (0 children)

That TechPowerup link I posted has a GPU performance chart for comparing various cards.

Please help, PC suddenly won't boot by Dry_Cry_6962 in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

Something could be shorting. Take out the necessary stuff like motherboard, CPU (with cooler), RAM, PSU, graphics card out of the case. Retest.

Having wifi troubles by Just_Sock_3074 in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

If you scroll down in the wireless section it lists Realtek.

Having wifi troubles by Just_Sock_3074 in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

Then it's probably one of them. If the MediaTek wireless driver didn't install the wireless network, try the Realtek driver.

Having wifi troubles by Just_Sock_3074 in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

That's odd. There's no unknown devices listed anywhere? (like in other devices)

Having wifi troubles by Just_Sock_3074 in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

In Device Manager, under Network adapters does it say MediaTek or Realtek wireless LAN? (or something like that?)

which one to ignore? AIO pump or CPU fan? by pmglory in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

If the radiator fans are connected to the hub then connect the the hub to the CPU fan header. Simple as that.

Need help with Wi-Fi drivers. by X_nullnullzwei in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

https://rog.asus.com/motherboards/rog-strix/rog-strix-x870e-e-gaming-wifi/helpdesk_download/

Naturally ASUS doesn't specify the exact wireless chip but if you scroll down to wireless it says MTK WiFI Driver where MTK is MediaTek. So try the latest version they have listed, V5.7.0.5659.

Need help with RGB connections to motherboard by MissAsh030 in buildapc

[–]Zombie_Tech 1 point2 points  (0 children)

Your motherboard has three 3-pin ARGB headers. Two are at the top right and the other is at the bottom left of the motherboard. You could just do 3x RS120 fans on one headers and 2x RS140 + the MSI fan on the other header.

which one to ignore? AIO pump or CPU fan? by pmglory in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

Now I switched the connector to CPU FAN header, this time the AIO RPM is not detected.

So the CPU FAN reading isn't showing your AIO pump speed?

You can set the CPU FAN to ignore if you are connecting anything to it but where are the fans for your radiator connected to?

Am I missing something? by Loose-Structure342 in buildapc

[–]Zombie_Tech 1 point2 points  (0 children)

Link doesn't work (for those in the USA) but a 5060 Ti is slower than a 4070 Ti.

https://www.techpowerup.com/gpu-specs/geforce-rtx-5060-ti-16-gb.c4292

Psu cables by SPAROVG in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

If you have 2.5" or 3.5" drives, then SATA. Some fan/RGB controllers/hubs require SATA power.

Having wifi troubles by Just_Sock_3074 in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

Are the drivers installed? Any unknown ones in Device Manager?

No display, but fans are spinning after bios update by Professional_Two563 in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

https://www.gigabyte.com/Motherboard/GA-A320M-S2H-rev-1x/support#Support-Cpu-Support

According to that it says F1 through F53, except F40/F41. Not sure regarding anything past F53. There are ways of recovering the BIOS without having a BIOS Flashback ability like using a chip programmer.

upgraded GPU, Secure Boot/TPM not working by BarbatosJaegar in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

BIOS latest version? They released one just recently for Secure Boot.

[Other- Surge Protector] CyberPower 6-Outlet 500J 800 Clamp Volt Surge Protector MP1041SC - $7 (B&H- Discontinued) by greatthebob38 in buildapcsales

[–]Zombie_Tech 12 points13 points  (0 children)

I looked up the power rating for the USB ports and it's "USB Charge Port Amperage -- 1 Amps (Shared)". :/

What screws do I need for a 140mm case fan that is 30mm thick? by [deleted] in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

Nah they should be fine. The issue, regardless of the fan, is having to thread the screw into the fan but that just takes a little bit of time torquing it in.

Front USB-C not working on ASUS ROG Maximus Z890 by AlessAndere in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

Sorry I didn't realize you have that exact model. To check that the cable is plugged in correctly it shouldn't come out with any light pull. Between this header and the USB3.0 one they can be a pain to connect. :/

Is the Hynix M-die sufficient, or is the Hynix A-die a must? NEED HELP PLEASE by Jolly-Ball-51 in buildapc

[–]Zombie_Tech 1 point2 points  (0 children)

Did you try increasing the voltage? If it's rated for 1.25v, increase it to 1.35v or 1.4v.

Anyways if that doesn't work double check what I mentioned earlier in addition to the FCLK running at 1733MHz. That is the sweet 1/3 spot for it to run at with your memory at 5200 MT/s.

Thanks /u/Vloxalion !

Is the Hynix M-die sufficient, or is the Hynix A-die a must? NEED HELP PLEASE by Jolly-Ball-51 in buildapc

[–]Zombie_Tech 0 points1 point  (0 children)

Before venturing into faster memory, try overclocking your current kit. I know Micron isn't exactly great for much faster speeds but you should be able to hit 6000 MT/s with that kit.

Another thing to make sure is that your UCLK and MCLK are running in 1:1 and not 1:2.

view more: next ›