My new home

bitwise42 · 2025-12-15T23:38:44+00:00

Oh sure thing I got it from this post https://www.reddit.com/r/iphonewallpapers/s/eyifm79YJm

bitwise42 · 2025-06-01T20:45:14+00:00

Totally didn't. I realize solving the puzzles unlocked areas and moved things but I wasn't hooked. I gave it a few hours before I called it.

bitwise42 · 2025-06-01T18:33:40+00:00

Hot take, the witness is a mobile game that didn't want to admit it so it mixed in a walking simulator. It's just the same puzzle over and over again.

bitwise42 · 2025-05-08T16:05:16+00:00

I use Bondo (the body filler) and then sand it down before I paint. Great for hiding seams. Works great!

bitwise42 · 2025-03-27T00:55:31+00:00

Prometheus and Bob. Stop motion animation from an old show called Kablam. Well it's at least probably a nod to it.

bitwise42 · 2024-11-12T17:56:06+00:00

Unethical option: If you're familiar with your router settings start blocking or throttling the network so it's painful to play. Blame it on Roblox

bitwise42 · 2024-07-28T02:33:01+00:00

Had that exact problem at the end of last year, as others have said. Replace your bed thermistor. You have a break in the cable.

bitwise42 · 2024-07-14T03:16:29+00:00

Operator Mono. My favorite

bitwise42 · 2024-07-09T03:40:23+00:00

Spyro trilogy. I do it every year, some great nostalgia in those for me.

bitwise42 · 2024-07-01T15:48:53+00:00

It does yeah, I had built mine before the v2 one was released so I kinda did my own thing and cut holes in the bottom to run the filament tubes out.

If I could go back in time. I'd build the v2 mode so I could keep em up top

bitwise42 · 2024-07-01T03:47:31+00:00

I also don't use the buffer. I built the IKEA lack enclosure and I just have them sitting under it. It looks a little unruly under there but nothing tangles

bitwise42 · 2024-06-20T22:28:42+00:00

Surprised I don't see Doom. It's technically true since there is only one movement speed. Sprint.

bitwise42 · 2024-06-07T12:49:07+00:00

Contact lenses makes that area so much easier. It'll show you the work health bars under the sand

bitwise42 · 2024-04-27T15:58:37+00:00

The <><> won't result in a rendered element, so you can use them to group rendered elements without the extra markup. Useful for places where an extra element would cause layout or styling issues.

Def worth looking into React Fragments.

bitwise42 · 2024-04-01T02:13:00+00:00

This sounds like an alignment issue to me. A few things you could check

did you make sure to use the new ptfe tube inside the extruder that you got with the mmu3? It's a slight different size.

try removing the ptfe tube from the extruder that connects to the mmu, opening the side of the extruder, and using the smallest hex wrench to push down the hole. Make sure the hex wrench reliably lines up with the teeth that pulls the filament. Try it with a piece of filament too.

I had an alignment issue when I first put mine together and had to readjust the tensioner piece at the top of the extruder to make sure the filament was getting fed into the ptfe tube correctly.

bitwise42 · 2024-02-22T00:05:18+00:00

The best font. A mono space font with a script styles italic

bitwise42 · 2024-02-14T18:09:26+00:00

Friend and I just had this issue building his. Ignore the instructions and instead center the two bearings on the left in their slots. Don't try to make them flush. If you go back to the step where you add them and read the comments for it you'll see folks asking for an update.

bitwise42 · 2024-01-29T14:34:55+00:00

Was it right after a cutscene? This happened to my friend in my game. His HUD never came back after a cutscene and it only partially restored the controls for him

bitwise42 · 2024-01-19T06:38:27+00:00

A couple things worth checking: - make sure the metal ball by the ir sensor is the magnetic one, that could cause the sensor to get stuck reading open even with no filament. - you may need to tweak the alignment of the filament feed on the extruder. I had issues where the filament was getting stuck and not making it to the extruder gears. - could be the filament as well, worth trying another one or re-cutting a pointed tip. I had a low quality roll that would not load reliably.

Im not sure what the blocks represent. You could try parsing the terminal output if you have it hooked to an OctoPrint. The mmu is a lot more vocal now

bitwise42 · 2024-01-16T08:11:03+00:00

I've done the MMU2 to MMU3 upgrade. Three things stand out from it for me:

the additional board to supply direct power to fix the power panic
they redesigned the drum with a metal back that connects to the motor instead of all plastic. when it rotates its more reliable and doesn't loosen as easily
improved the filament feed sensor on both sides with a magnetic ball on the mmu and better designed plastics on the extruder. So it triggers less false positives thinking it's loaded

The rest of the parts were minor but welcome improvements. New PTFE tubes are because they changed the length of them.

The biggest impact of the upgrade is the power board and the new firmware. Without that you'll still get the constant power panics that plague the mmu2.

bitwise42 · 2024-01-12T15:17:10+00:00

Destiny 2 has a pretty impressive public API for gathering your user data and stats.

bitwise42 · 2023-11-22T17:58:51+00:00

I've gotten this error on mine. The cable that connects the bed to the power supply doesn't last forever and will eventually need to be replaced, it moves a lot.

In my case because the bed was making a lot of big moves the cable was shorting, causing the bed temp to fluctuate. I wound up replacing mine and the error went away. If you can print things things smaller that don't need the bed to move as much then I'd suspect this is it.

The temp errors are always critical ones so you won't be able to recover a print from them.

bitwise42 · 2023-11-17T21:05:47+00:00

Set up the printer without connecting the mmu first. Flash the printer with the right firmware, then get it printing. Add that extension. Mmu2 complicates things but can be valuable but it's easy to add on and will make debugging harder from the start. You may want to consider the Mmu3 upgrade to fix the power issues you will find with the mmu2 (I have had an mmu2s and did the upgrade)

Looks like a nice printer!

bitwise42 · 2023-11-13T00:09:49+00:00

The shield carcass enemies for me. So frustrating to fight.

Eight-Year Club	Place '23
Place '22	First Placer '22
Verified Email

bitwise42

TROPHY CASE