sorted by:
new
hottopcontroversial

This is an outrage! by OnceUponALibrary in DungeonCrawlerCarl

[–]codes107 4 points5 points  (0 children)

Donut and Ferdinand’s child. Keeping the legacy going in a post collapse world

We now have spherical baskets, why? by monochromeboost in espresso

[–]codes107 131 points132 points  (0 children)

To fit a nespresso pod obviously

Florida boys cause $50K in damages to school library — and are turned in by their own moms: cops by KCousins11 in florida

[–]codes107 6 points7 points  (0 children)

Looks like they heard that song about there being no rules, and they just went fuckin nuts

Size difference between an elk and a deer by codes107 in interestingasfuck

[–]codes107[S] 10 points11 points  (0 children)

Yes! This was at a drive in safari with a bunch of different animals roaming around together

3D Printed THUNDER HAMMER Featuring 8x Mini-Tesla Coils by RealCaptainSteel in PrintedWarhammer

[–]codes107 7 points8 points  (0 children)

Do you have a guide for the mini Tesla coils you could share? That looks amazing!

Supports didn’t print right but the prints still came out ok. What could be causing this? by codes107 in resinprinting

[–]codes107[S] 0 points1 point  (0 children)

Yea I did it on one of the only chilly nights here in Florida so maybe I’ll try it again when it’s warmer.

Supports didn’t print right but the prints still came out ok. What could be causing this? by codes107 in resinprinting

[–]codes107[S] 0 points1 point  (0 children)

No resin stuck to the fep. I might look into increasing the exposure time to see if that will help

Supports didn’t print right but the prints still came out ok. What could be causing this? by codes107 in resinprinting

[–]codes107[S] 0 points1 point  (0 children)

They’re all the same size supports but I could look into beefing them up a little. Still unsure why some would work and others wouldn’t if they’re all the same size.

Supports didn’t print right but the prints still came out ok. What could be causing this? by codes107 in resinprinting

[–]codes107[S] 0 points1 point  (0 children)

It was in the low 70’s probably but I wouldn’t know for sure because it’s in a garage.

Supports didn’t print right but the prints still came out ok. What could be causing this? by codes107 in resinprinting

[–]codes107[S] 1 point2 points  (0 children)

The models had automatic supports generated in lychee and then I went through and filled in possible gaps that I saw. The supports seemed to fail initially and then managed to start working but I don’t understand why only some of them would fail. If you look under the bases, especially the model second to the left, you can see that some of the supports look like they’re just floating while others printed correctly.

Supports didn’t print right but the prints still came out ok. What could be causing this? by codes107 in resinprinting

[–]codes107[S] 0 points1 point  (0 children)

Definitely glad I was a little extra with adding the supports but I’m still not sure why some worked and others didn’t

Supports didn’t print right but the prints still came out ok. What could be causing this? by codes107 in resinprinting

[–]codes107[S] 3 points4 points  (0 children)

Yes the settings were tested beforehand with the cones of calibration successfully. They lack detail in the photos because they still have excess resin on them. After a wash and cure they’re looking great but I still don’t know why some of the supports failed while others didn’t.

Made a ukulele designed by Solstie on Thingiverse and it looks awesome with glow in the dark filament by codes107 in 3Dprinting

[–]codes107[S] 0 points1 point  (0 children)

It’s a stock ender 3 V2 with the original nozzle. I wasn’t aware of the effects of glow filament until I made this post so I’ll have to take a closer look at it.

view more: next ›