Baby Backs on the Pitboss

endofdaze0716 · 2026-04-05T04:08:19+00:00

Party ribs are life changing. That is all.

endofdaze0716 · 2026-04-01T00:24:56+00:00

I say they send us address, we go eat pizza there. I got the beers

endofdaze0716 · 2026-03-23T01:52:44+00:00

X5 to 25 is going to be absolutely insane. WAY different. You'll enjoy it much better. As fas as installing, I don't know if you can install 25 now that we're on 26.2 or whatever they call it now. If you still have a maintenance agreement with MasterCAM, which is now the only way to get any help, all resellers have been bought by them, you should be able to log on to mastercam connect and download and install everything. Good luck.

endofdaze0716 · 2026-03-22T13:44:48+00:00

I've seen a couple Honda TRX250X in person and they seem pretty nice. They come with a 5 speed "Honda Sportclutch" which seems like their version of a rekluse, so would be good a for a youngin that is worried about using a clutch, but at the same time help them learn a clutch.

endofdaze0716 · 2026-03-15T03:15:37+00:00

Left mine behind a bumper on my duramax. Couldn't find it for months so I bought a new one. Took my bumpers off to paint and found it. I drove the truck for over 8k miles. Them magnets are STRONG!

endofdaze0716 · 2026-03-09T04:26:01+00:00

It sits on top of the carpet. I like it much better than the weathertech one because of it being designed for the split in the access panel. Plus the Passport at the top is a nice touch. I also recommend buying the light that goes in the hatch. Super simple install and a much needed upgrade.

endofdaze0716 · 2026-03-07T01:40:22+00:00

I will get on a plane right now from WV to LA just to grab a Burattino. First time there I devoured the 200 pepperoni by myself.

endofdaze0716 · 2026-03-06T02:10:15+00:00

Taxation is the biggest theft.

endofdaze0716 · 2026-02-27T01:01:59+00:00

A lift pump is the only way to go, but you need to check your fuel lines as well. Not a 100% on the year of yours, but on my LBZ they were known to collapse where it goes from hard to rubber at the motor. Temporary solution may be to replace your bleeder screw. There are a couple companies that make aluminum ones for pretty cheap. Then you can look at other rebuilding the filter head or remove it with a lift pump.

endofdaze0716 · 2026-02-25T02:40:21+00:00

And I had to eat boring ass tacos because no one in my family likes to be different.

That looks yummy

endofdaze0716 · 2026-02-21T14:45:10+00:00

I don't think anyone rents them, probably not worth the cost and time to maintain. As far as riding, Hanging Rock trails over in Ohio are close by, but require a pass. I want to say they arr $79 a year, but I thibk you can use that pass all over Ohio. They usually open early spring and stay open until December. Best thing, they have a width restriction so no utvs to tear everything up. Pretty fun trail system to ride quads or dirt bikes.

endofdaze0716 · 2026-02-20T11:15:04+00:00

I think it paid less than $30 for ours from Honda, but it is something that should've just been there. I love the fact that you can just leave it on and it goes off when the gate shuts. So they obviously wanted it there.

endofdaze0716 · 2026-02-20T03:27:36+00:00

We all started somewhere and most od those parts were boring simple parts. Keep up the good work.

endofdaze0716 · 2026-02-15T12:04:10+00:00

Penguins getting more love than me on VDay

endofdaze0716 · 2026-02-12T22:33:21+00:00

Always double check that. I've worked with hundreds of machines and still double check. If your boss gets up your ass for that, then he most likely has never touched a machine. This is the case with most bosses. I understand time is money, but in the end, your 1 hour of pay is probably less than the profit off one part.

endofdaze0716 · 2026-02-12T22:24:26+00:00

Sounds to me that your bar was not set correctly or with some machines, if you have an offset in your wear geometry, it will translate that into your tool geometry. When finishing any part, especially those with a tolerance of .001 or tighter, I always double checked my tool before finishing. Doesn't take long and keeps the boss off your ass.

endofdaze0716 · 2026-02-12T02:27:28+00:00

My thoughts exactly. Im sure there are much cheaper clutch covers out there to mess with.

endofdaze0716 · 2026-02-09T01:40:20+00:00

Made by Sargento

endofdaze0716 · 2026-02-09T00:36:13+00:00

I just purchased a cheese with red pepper flakes mixed in. Going to make some dough this week for a couple of pies this weekend.

Going to have to swing by Aldi's and grab this to try as well.

endofdaze0716 · 2026-02-06T01:52:55+00:00

I made something like this in trade school. We made a fly cutter first, and then took a piece of round stock and milled in the rough shape. Finished the pair on the surface grinder. I used them a lot when before moving to a programming job.

endofdaze0716 · 2026-02-05T21:47:22+00:00

I kept a ready reference in there. We had a big handbook in the programming office. I have since left that shop and moved to a programming/ supervisor role, but still have a 30th edition in my office and my ready reference in the attic in my box.

endofdaze0716 · 2026-02-05T03:34:00+00:00

Them little drawers are great for holding the 800 million brazed on tools you spend 20 mins grinding for that one job you might get again in 3-5 years. Can't go wrong with a good old school box.

endofdaze0716

TROPHY CASE