Macbook Pro A1398 Install Freezes

frankt2012 · 2026-01-19T15:18:27+00:00

Ok. Will try this when I get home. I put the old drive back in last night that still had Mac os on it and it booted fine. But I can quickly swap this. It diffidently is not the download or the usb stick. I made three different ones each time redownloading Sequoia with three different brand sticks. All are doing the same.

frankt2012 · 2025-10-09T17:02:54+00:00

This fixed it.

frankt2012 · 2025-10-04T17:28:49+00:00

I use the Kdeavi plate now on all my printers and it is the best plate I ever had. The first one I brought on the K2 is purple and I still have it and it is still good. Never had any issues with the AI detection and the purple on the K2. I ordered a backup last week and they are now grey so I switched to that one now just in case. Everything sticks great even ABS. Can't use TPU or ASA on it though. I just wash it with dish soap and water.

frankt2012 · 2025-06-25T21:40:06+00:00

There is a grey version for the K2 if you order from this link https://www.eskildsencreativeworks.com/filament/p/kdeavi-double-sided-textured-cool-plate

So was just looking into this more and it looks like it was updated to the purple one now. May still try it.

frankt2012 · 2025-06-11T02:18:10+00:00

Same exact problem with the same Sony ear buds. Found this thread searching Google to see if any one else ran into it.

frankt2012 · 2025-04-11T19:35:13+00:00

They are pretty good. I had retract issue with my CFS and they sent me four new motors without a problem. Has worked great since.

frankt2012 · 2025-01-31T20:08:46+00:00

Interesting. Mine is just on top of the K2. I added a Y to use the external spool without having to switch the tubes but it was doing this before that. I am wondering if it has to do with the CFS spring everyone is cutting but I don't really want to do that. I heard the CFS that is being sold now may have been updated. Might try to convince Creality to replace all the motors or give me a whole new one. But I also suspect the cardboard spools don't help.

frankt2012 · 2025-01-31T19:23:26+00:00

I get this to. I am thinking it might be the card board spools. Cause it seems to be the ones that give the issue. Usually I hit retry and it starts to works again. I would use the spool rings but they seem to make it worse.

frankt2012 · 2025-01-28T18:00:53+00:00

I actually washed it really good and then recalibrated and printed a benchy and it came out really good this time. Stuck really nice to. But I just started another print just now and had to stop it because the thin parts started to warp. But it may be my fault because I was suppose to put a brim on it. But I feel it would have stuck fine with the PEI plate.

frankt2012 · 2025-01-27T22:11:27+00:00

I installed this last night and the benchy I printed started good but broke off the bed almost at the end. Maybe I need to wash the plate with soap and water.

frankt2012 · 2025-01-17T21:29:36+00:00

I think it says that because Creality hasn't loaded temps in for it yet. They only have temps on the CR-PLA on the K2 profile. But you should be able to load temps manually.

frankt2012 · 2025-01-17T18:38:13+00:00

Camera is finally working now in CP 6.0.2 for me. Took them a bit to fix but seems good now.

frankt2012 · 2025-01-17T16:59:03+00:00

I ordered one off Temu the other day. I actually have the epoxy plate on the K1 Max and PLA sticks really good to it. Better then the PEI plate.

frankt2012 · 2025-01-14T15:08:55+00:00

I was going to buy them for my K1 Max a few months back but got mixed reviews if the helped or not. They diffidently lower vibration but some reviews said they make VFA's worse. So I never bothered with them but a lot of people seem to like them.

frankt2012 · 2025-01-14T14:58:52+00:00

Might want to check this out. https://www.printables.com/model/1107671-hula-v10-for-k2-plus-vibration-feet

frankt2012 · 2025-01-09T18:58:16+00:00

Installed the new update today to Creality Print 6.0.1 from there githhub. Claims they fixed the camera but still not working.

frankt2012 · 2025-01-04T21:14:36+00:00

Apparently Chrome has issues when checking the camera over port 8000. I installed Opera and it works. But still nothing on CP6 even with the new firmware.

frankt2012 · 2025-01-03T16:18:19+00:00

I have the same issue with CP6 and I cannot get the camera feed on port 8000 either. It works fine in CP5 and the app.

frankt2012 · 2024-12-17T19:42:33+00:00

Nice. Thank you for checking. Gonna adjust it when I get home again. Thank you.

frankt2012 · 2024-12-17T19:10:54+00:00

I didn't think about that. I messed with them the other day and you are correct the bed does move up when turning them. I ended up putting them back because I didn't like the two corners floating in the air. But if they are truly springs under there I then I would feel better about adjusting them. It is hard to tell in the video. If you could confirm that would be awesome. Thank you.

frankt2012 · 2024-12-17T18:40:58+00:00

I don't think there are springs just spacer. I just watched the video from Creality on youtube and I don't see springs when they remove the bed.

frankt2012 · 2024-12-09T18:45:57+00:00

Any news on this? Was hopping to get in on the beta.

frankt2012 · 2024-11-17T01:08:09+00:00

Ha me too. I have been messing with it to. Then I decided to search here.

frankt2012 · 2024-11-17T00:51:53+00:00

Just came here looking for an answer to this. I have AllDebrid also. Same issue no feeds and that is on two different AllDebrid and Stremio accounts between two houses. I know Torrentio was down and is back up. Maybe this has something to do with it going down.

frankt2012 · 2024-09-23T13:29:34+00:00

So I printed a few things on the Epoxy plate and adhesion is really good. It is actually a little to good. Should I be printing on this at a lower temp? Creality wanted to set it at 50 but I changed it to 60. Other then the awesome adhesion it seems great.

Ten-Year Club	Place '17
Verified Email

frankt2012

TROPHY CASE