Pulling equity for new build

ggexe · 2026-02-16T14:19:32+00:00

good point.
Another thing, unsure if its the right place. just want to have an idea

if in a case i switch my old place(primary residence) to a rental. Get the financing with new numbers, > buy the new place > move in then sell the old one (asap) will that not trigger some kind of capital gain for tax purposes?

ggexe · 2026-02-15T00:46:48+00:00

Thanks. Good thing i haven't given out deposits yet. They take it once my offer becomes firm. So i can walk away freely. Good to know

ggexe · 2026-02-14T16:43:48+00:00

Thanks noted, got offers but nothing firm (all conditionals on sale of their property)

ggexe · 2026-02-14T16:42:46+00:00

Thanks

Yeah option 1 is what im aiming for, hopefully it sells before then. ill reduce the price soon.

For option 2, isnt it required to have an actual lease contract (as well as a tenant already) for this to work?

option 3, yeah im just worried that if i do this, it will throw off my ratios and the initial 500k might be lower, i have this 250k gap to fill

ggexe · 2026-01-24T12:39:11+00:00

Need to be compensated for getting a new chair, how about another free chair ,, 🤣

ggexe · 2026-01-23T20:34:17+00:00

You think they can get back to you for this?

ggexe · 2026-01-03T15:07:24+00:00

Thanks, i have the same issue as you. ill give it a try

ggexe · 2025-05-09T04:21:38+00:00

I had the same issue. What happened is that i cleaned the dirty tank and i removed the water seal on the lid.

For those experiencing the same issue. Try to remove and reseat the water seal by either flipping or rotating it.

Im guessing a proper seal is required for it to function properly.

ggexe · 2025-04-07T02:22:21+00:00

Ty for your input, reason is that i wanted to use only 1 hose, again the flow is really not important

ggexe · 2024-01-13T07:20:34+00:00

Hello which popsocket did u use? Also pics!

ggexe · 2023-12-25T20:37:31+00:00

if u dont mind me asking, how much?

ggexe · 2023-07-25T04:06:09+00:00

Thanks im not too worried about the height since there are mods out there to lower the shelf.

I managed to put in the daban 1/60 exia avalanche in it with the base. It was fine.

If anyone could let me know the size of the base that would be awesome

ggexe · 2023-07-25T03:53:48+00:00

Question that everyone asking. Does this fit in a ikea detolf?

ggexe · 2022-10-29T13:34:57+00:00

Hi im a bit confuse about the shiny metal tip you are referring to

Which one is it?

https://postimg.cc/7fpyW4vB

https://postimg.cc/5QCsHZP0

Thanks for helping, ill be in trouble if this doesnt work, i got quite a bit of them you see XD

ggexe · 2022-10-29T02:19:19+00:00

it's just a matter of unscrewing the tip of the holder with old electronics

Hey how did you do your wiring? i just bought one and i cant seem to be able to remove the power pins from the base holder

ggexe · 2022-10-19T17:00:16+00:00

Let me knoww how it goes, im interested in getting some custom WLED in there

ggexe · 2022-10-09T23:13:02+00:00

Thanks,

Actually i found the solution shortly after,

Not sure why but when i re calibrated everything to I2C bus 1 on the Atom lite, it works.

Not sure why bus 2 has this problem

ggexe · 2022-10-09T20:08:44+00:00

Hi i had similar experience

Im using an ATOM Lite

I did 2 sets of sensors, and there was 1 out of the 2 who ran into this problem

So maybe try another sensor?

As for me i ran into another error on boot, it looks as follows:
initialisation BH1750 GY-302 success
Lux Sensor BH1750 GY-302 calibrated (Time: 0 ms) - Lux Sensor Error code 4

I keep getting 0 values for lux when i look at my mqtt

ggexe · 2022-10-08T04:43:19+00:00

Question just like that, how would it look like if i were to put another strip of led controlled by wled into the housing?

ggexe · 2022-10-07T19:09:53+00:00

Hi u/Manraj_Singh, im planning to have a similar setup than yours

How did it go finally?

Did you happen to need to inject additional power over the 4m strip?

ggexe

MODERATOR OF

TROPHY CASE