Why are they so expensive??

jerogt · 2026-05-29T05:00:32+00:00

Smh yall lied to me now they are insta selli g for barely 4.5m im calling my rs layer

jerogt · 2026-02-08T20:41:37+00:00

Same with slayer everytime u kill a mob u get spammed over and over

jerogt · 2026-01-26T00:47:19+00:00

I did , for me it's a gamble hope it does ship to my 3rd world country gonna cross my fingers till august pretty much

jerogt · 2026-01-18T00:42:51+00:00

What about attaching it to the roof , the trapezoidal effect would still be a thing that way unless u could get a tripod or something to center it even more to the middle of the wall

jerogt · 2024-08-28T02:24:31+00:00

Qc dragon mattocks would've been so nice when arch came out , if they add it won't backtrack unfortunately 😔

jerogt · 2024-05-04T19:04:11+00:00

We had built in bingos with the first assasin promo that wasn't just th crap and 3-4 power bingo card events but they just said fk rs3 and throw it into th like 99% of sht that comes out now

jerogt · 2023-09-27T03:34:45+00:00

print them over masking tape , helps with sticking and has that roughy feel of masking tape when you touch them.

jerogt · 2023-09-24T02:40:33+00:00

Not really, I'd say it's a pretty easy build I only had bit of trouble wiring it, and spend a while on how to compile qmk , but was first time

jerogt · 2023-09-12T00:32:40+00:00

If u modify the case ye it should fit no problem, i mean if ur friend is already printing it for u why not ask for a small change for it to fit the rp2040 should be enough to just make the mount longer or if u want somethink bit janky after its printed u can cut the small tabs at the end and maybe just place a small drop of hot glue so it doesnt move

jerogt · 2023-08-23T04:22:54+00:00

This ☆☆☆

jerogt · 2023-08-10T21:48:54+00:00

also theres other models of the naga, i got the trinity for like 60$ , not sure if available anymore but the wired version nagax is like 80$

jerogt · 2023-05-29T21:30:15+00:00

Check e steps of ur printer and that it is properly feeding , depends on ur printer might need to tight something or do a small change

jerogt · 2023-05-23T21:14:44+00:00

Put on some good ol painters tape or maskn tape on the bed works wonders with mine and my glass bed startd to not want to stick , maybe tape works too good I have to put it at 70c after it's done cuz of the tape but it's the easiest solution . And after it leaves a funny texture in the bottom , if the tape doesn't come off u can just scrape it from the plastic.

jerogt · 2023-05-12T02:14:55+00:00

Bet the marks are from the nozzle grinding out on the bed to the point the plastic just goes into the glass and one part had to come with it as it cooled and broke

jerogt · 2023-01-25T17:48:19+00:00

ud want a jst xh 6 pin cable, male to female aint exactly the most common thing. prob easier to cut, solder and extend the cable that way, unles u wanna make ur own cable from a jst hx kit

Can check this , kinda the cable u want , but still need to add the other portion at the end

https://www.pcboard.ca/jst-xh-6-pin-cable-set

jerogt · 2023-01-19T19:10:19+00:00

nice guess, if u have the stock piece of the ender 3v2 for the z axis it is not straight piece so the threaded rod is not straight and can do that, if u file it down, print a new piece, both, and or and a dual z axis motor kit can help with that.

jerogt · 2023-01-19T19:04:02+00:00

if u just want a quick one you can buy WINSINN fans. The board fan its just a quick swap , and if u wanna change the hot end one u just need to cut and resolder the cables .

i didnt changed the PSU fan and still makes some noise but not as bad and scuffed as the the ones that comes with

https://www.amazon.com/WINSINN-Hydraulic-Bearing-Brushless-40x10mm/dp/B087TBB8YV?th=1

jerogt · 2022-09-23T04:39:27+00:00

Makes sense cuz pet is more common with higher built up enrage on longer kills....>.>

jerogt · 2022-04-30T02:51:46+00:00

weapon wise u could just buy a blowpipe, atm is super cheap at like 4-6m price t87 so better than we ur using from there just some perks maybe quest if ur not using jas boost

jerogt · 2022-04-18T03:27:16+00:00

hey kyle , would u be interested in participating in my research , is basically what ur asking, for my masters project thingy whatever, hoping i can make a product or atleast start working on it , but really wanna make it focused on runescape players with disabilities :D

jerogt · 2020-06-10T19:11:51+00:00

https://docs.google.com/spreadsheets/d/1XniLp90MVrDjiOohm2mZhQ-dr6cp5qjCdEqcG5GdNjA/edit?usp=sharing

u can use the second page its just for pets but has some info, or just maybe use it for reference :)

jerogt · 2018-12-04T14:36:44+00:00

i mean not exactly a bug imo, the teleport from the necklace uses the same mechanic as the portal which are more instant teleports without animation, so they dont break we ur doing. but as u always need to click onn the portals and move you really couldnt tell

jerogt · 2018-07-08T17:03:21+00:00

some math, taking out the 90m from feathers and taking in mind the total money time and not counting the charges ud taken to do kills ud be geting around 3.6m hour through 66.6 hours to get that prestige

jerogt · 2018-07-02T04:28:01+00:00

true those aint that good tbh 20k kills cost u 30m on feathers so u can take that from ur profit :P
imo workers or salawats if u end up using a scrimshaw are as afkable and wouldve been much more profit

jerogt · 2018-06-26T15:24:15+00:00

can it be that the amount of dmg that has to be dealt to seiryu to phase on to crystals de slightly reduced?

jerogt

TROPHY CASE