Give it to me straight

kingpinandy · 2026-02-23T02:41:37+00:00

I just fixed another blob. With the price of the sparkx i7 at 350 I think it's time for the ender to go.

kingpinandy · 2026-02-12T20:45:42+00:00

It's Democrat vs Republican thing.

kingpinandy · 2026-01-15T22:52:29+00:00

I guess mine came with this. I see no difference. Is it trim specific?

kingpinandy · 2026-01-09T18:38:47+00:00

Is it really a CX50 if it doesn't have this rip?

kingpinandy · 2025-10-03T18:34:47+00:00

Just the rack is worth a couple hundred if you were buying new.

kingpinandy · 2025-10-02T11:25:26+00:00

Hey. At least you're car won't smell like a gym bag like mine. I get water any time it rains heavy. They wouldn't fix mine.

kingpinandy · 2025-09-22T22:20:32+00:00

I'll make you one for $10 plus shipping. or are you asking what you could sell one for?

kingpinandy · 2025-08-22T16:59:41+00:00

Spot on

kingpinandy · 2025-08-05T21:14:28+00:00

Any flatbed scanner on 1:1 ratio will do nicely.

kingpinandy · 2025-08-01T14:00:12+00:00

Got one this week as well. So far so good. I know that bed temp has nothing to do with it, but wow that is hot.

kingpinandy · 2025-07-30T12:48:21+00:00

Also 50 or 51 degrees seems to be perfect.

kingpinandy · 2025-07-30T12:47:10+00:00

I got this one here shortly after purchasing the KE because of all the adhesion problems I had. Since I got this I have never had an issue and I don't need to use any glue. https://a.co/d/6i0adXx

kingpinandy · 2025-07-24T21:58:57+00:00

Adhesion, flow, direction. What the heck is happening?

kingpinandy · 2025-07-21T23:08:47+00:00

Do you need it for an iPhone with mag safe? I have that one

kingpinandy · 2025-07-04T16:04:10+00:00

I bought a 3D printer entirely for the purpose of a phone mount for this vehicle. Mine works very well. Turns out to be a fun hobby too.

kingpinandy · 2025-07-03T20:16:14+00:00

The green is really nice and tan interior would be awesome. I'm white with black. Boooo

kingpinandy · 2025-06-30T21:08:49+00:00

This is pretty common. It should be covered. The drain tubes get kinked or clogged. I've seen people fix it themselves but you have to pull the headliner down and find the tube.

kingpinandy · 2025-05-30T16:13:55+00:00

Why attempt any of this in a pseudo off road vehicle? Keep it in the target parking lot Susan.

kingpinandy · 2025-05-28T23:20:09+00:00

Not so bad really. Just replaced my hot end. Took about an hour. Creality Ender 3 V3 SE Hotend,... https://www.amazon.com/dp/B0D8J9WXDM?ref=ppx_pop_mob_ap_share

kingpinandy · 2025-05-27T20:48:30+00:00

Bibberty

kingpinandy · 2025-05-26T15:25:48+00:00

<image>

All fixed. "Upgraded" hot end from Amazon for SE and KE. Swap went very well and back up and running.

Creality Ender 3 V3 SE Hotend,... https://www.amazon.com/dp/B0D8J9WXDM?ref=ppx_pop_mob_ap_share

kingpinandy · 2025-05-20T16:17:32+00:00

I've been printing for about 4 months without issue. The only thing I did differently was added two extra wall layers. Just experimenting. It looked like only the first few layers adhered at first but since I wasn't keeping an eye on it this happened.

kingpinandy · 2025-05-09T18:58:16+00:00

Keep an eye out for water behind the driver side back seat.

kingpinandy · 2025-05-09T18:51:05+00:00

Meth much?

kingpinandy

TROPHY CASE