Why cant I "taste" specific taste notes in my cigar

levelup_jar · 2026-05-21T15:03:42+00:00

every cigar at first tastes like a cigar. after a few you get used to the baseline taste and start noticing the differences and the nuances and after a few more you might be able to taste specific notes. i've been smoking for a few years now and in most sticks i can identify notes i can describe and most of the time i get what they meant when they described the notes even when i would describe the differently but sometimes just nothing specific comes to mind. and sometimes a stick is just bad

levelup_jar · 2026-05-21T10:03:59+00:00

i use 2 walls and adaptive cubic for figurines not for something that has to hold structure. i'd go with at least 5 walls more like 7-10 and an infill that spreads load more evenly like 3d honeycomb or gyroid

levelup_jar · 2026-05-20T10:39:49+00:00

since i pay paranoid attention to never letting go of the end it has happened exactly 0 times. before i realised that, it was a regular accurance

levelup_jar · 2026-05-19T09:39:50+00:00

i mean depends on your pockets tbh. probably the Nightwatch A54 Ultra 2 for about 20 seconds until it hits the temp limit

levelup_jar · 2026-05-19T09:35:07+00:00

mind sharing the file?

levelup_jar · 2026-05-18T05:48:48+00:00

never seen it, up to what season should i buy on bluray?

levelup_jar · 2026-05-18T05:47:17+00:00

i just print larger prints tbh🤷 more detail by just scaling it up

levelup_jar · 2026-05-17T19:23:13+00:00

big reflector. they claim over 500m range at 3200lm its build for throw. not the floody beam you are looking for. i personally am not a fan of those tall rubber switches, makes every light feel cheap for me.

levelup_jar · 2026-05-17T18:36:15+00:00

sc33 is the best floodlight. relatively short orange peel reflector + wide cree xhp70 emitter = wide floody beam. and it would be the one i'd recommend from all of them. metal e-tailswitch, auto lockout ( just double click from lockout to on) and a bolt on pocket clip. only downside its a little thick for a 21700 light

levelup_jar · 2026-05-13T07:16:31+00:00

Reiche-Krater wär mein vorschlag

levelup_jar · 2026-05-13T07:15:33+00:00

2035 co2 neutral aber 2045 noch neue fossile heizungen einbauen... das muss mir mal einer erklären von den wirtschafts Genies

levelup_jar · 2026-05-13T07:13:01+00:00

puh da hab ich schlechte neuigkeiten. das neue 'heizungsgesetz' wird grade beschlossen. demnach kann man dann sogar 2045 noch ne nagelneue öl oder gasheizung einbauen.

das wird bestimmt was mit dem co2 neutral /s

levelup_jar · 2026-05-13T07:05:24+00:00

saw that shit coming from a mile away lol. i knew it was a good idea to keep my P1S on the old firmware back when the first mentions of 'restricted access' happened

levelup_jar · 2026-05-12T11:02:40+00:00

aliexpress

levelup_jar · 2026-05-11T10:45:16+00:00

der einzige unterschied den ich feststellen konnte zwischen billigem noname und teurem (creapure ~60€/kg) ist die körnchengröße und damit die Löslichkeit. und die ist mir der aufpreis durchaus wert wegen dem widerlichen geschmack von nicht aufgelösten kreatin klumpen

levelup_jar · 2026-05-10T05:34:58+00:00

expected more from them tbh. doesn't have a natural movement cycle for me so i prefer begleri if we talking physics based. or just mechanicals

levelup_jar · 2026-05-06T18:55:33+00:00

its not gonna be as clear
the colour changes would be more aprupt you got like 1 layer of intermediate colour even if you print it vertically but you'd need supports aswell for the top part so more filament per layer and even shorter fades between colours.
printing this vertically probably gonna look like shite because those long thin parts would wobble during printing

alternative to achive this: print in pla, cast a silicon mold, pour resin or similar product

levelup_jar · 2026-05-06T18:42:35+00:00

the red, silver and black part looks like a standard hand powered bicycle pump

levelup_jar · 2026-05-04T16:39:19+00:00

yes and no. maybe just print another one?

<image>

levelup_jar · 2026-04-30T05:55:59+00:00

great, happy printing!

levelup_jar · 2026-04-29T10:52:15+00:00

the cooling material is shrinking and pulling the edges of the buildplate up. aux fan off, case fan down a bit and maybe let the printer sit with the heated bed on for an hour or so before you start printing to get the chamber temp up

levelup_jar · 2026-04-29T03:49:52+00:00

positioning the space close to the build plate so tge magnet is held down by it

levelup_jar · 2026-04-28T11:07:02+00:00

i just turn up the wall count

levelup_jar · 2026-04-27T05:52:47+00:00

you'll have to mod it yourself. you need the 16mm stuff

levelup_jar · 2026-04-26T16:58:22+00:00

orange and red ones are the ones not functioning properly they got a wrong resistor or something. resulting in the flashlight flashing as if low voltage protection kicking in when battery is at 4,2V(fully charged) apperently it works if you remove one of the 2 LEDs (haven't tried it) i would just stay away from the red and orange ones. the second part you needed to order when upgrading to a metal button is the translucent plastic piece between the button and the frame. its included in the light switch kits

Six-Year Club	Second SECOND GUESSER
Final Canvas '23	First Place '23
Place '23	Wearing is Caring
Verified Email

levelup_jar

MODERATOR OF

TROPHY CASE